Meinberg HR102/DC Technical Reference Download

Page: 3 / 47

Table of Contents

Imprint

microSync Introduction

Technical Specifications microSync Chassis

Important Safety Information

4.1

Important Safety Instructions and Protective Measures . . . . . . . . . . . . . . . . . . . . . . . . .

4.2

Used Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3

Security during Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4

Protective Conductor- / Ground-Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5

Safety during Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6

Safety during Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.7

Handling Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.8

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.9

Prevention of ESD Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.10 Return of Electrical and Electronic Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

microSync HR102/DC - Connectors

5.1

GPS Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2

Programmable pulse output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3

Time Code AM (modulated) Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4

Frequency Synthesizer Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5

RS-232 COMx Timestring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.6

Status Indicators - CPU and Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7

USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.8

LAN Network Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.9

DMC X2 Terminal Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.10 Fiber Optic - Programmable pulse Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.11 DMC X1 Terminal Connector / DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GNSS Satellite Navigation

6.1

Time Zone and Daylight Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation GPS Antenna

Starting of Operation

8.1

Initial Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.1.1

Network configuration with the mbgOSWizard . . . . . . . . . . . . . . . . . . . . . . . . .

8.2

Initial Start of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Appendix

9.1

Technical Specifications GNSS Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.2

Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.3

Protocols and Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.4

Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10 Technical Appendix - GPS A Accessories

10.1 Antenna Cable: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.2 Antenna Short-Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.3 Technical Specifications - MBG S-PRO surge protection . . . . . . . . . . . . . . . . . . . . . . .

10.3.1 MBG S-PRO - Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.3.2 Installation and Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11 RoHS and WEEE

Date: 29th July 2021

microSync

Summary of Contents for HR102/DC
















































Search results

Summary of Contents for HR102/DC

Reviews:

Related manuals for HR102/DC

Brands by name

Popular brands

Meinberg HR102/DC, Technical Reference

Search results

Summary of Contents for HR102/DC

Reviews:

Related manuals for HR102/DC

Brands by name

Popular brands