21
Before Contacting Authorized Dealer
• Ensure that the appliance is plugged in the outlet
and that the fuses are OK.
If the Lighting Does Not Operate:
• Ensure that the appliance is plugged in the outlet
and that the fuses are OK.
• Check the bulbs. Always unplug the appliance
during this check. Tighten if the bulbs are loosened;
you may replace them if they do not turn on although
you have tightened them.
Possible Faults and Things To Do Before
Contacting the Service:
A) If the appliance does not operate
anyway:
- Check the fuse that the appliance is connected and
main fuse of your home.
- Check whether the hood is plugged and whether
the plug is fully seated on the outlet.
B) If the performance of the appliance is
not enough or operates loudly:
- Is the outlet diameter of the flue adequate? (min.
120 mm).
- Are metal filters clean? Check it.
- Ensure that the carbon filters are not older than 6
months if you are using the hood flueless.
- Make sure that your kitchen is adequately ventilated
to ensure the air flow.
Contact authorized service if the performance of
your appliance does not still satisfy you.
If the hood does not operate:
Before contacting the service:
Ensure that plug is installed on the outlet and that the
power fuse in the installation is OK; do not perform any
operations that may damage the appliance. Check
your appliance as per Table 1 before contacting the
service. Contact your dealer or nearest authorized
service if the problem is resumed.
Replacement of Glow Bulbs
Disconnect the hood from mains.
Remove the aluminum cartridge filter. Remove
the faulty bulb and replace with a new one with the
same rating. (Lamps may burn your hand when they
are hot, wait until they are cooled off.)
Figure 17
Figure 17
C
h
e
c
k
e
le
c
tr
ic
c
o
n
n
e
c
ti
o
n
(V
o
lt
a
g
e
o
f
th
e
electri
c
network
shoul
d
b
e
between
220-240V
,
cooker
hood
shoul
d
b
e
connected
to
grounded
Check
motor
switch
(Motor
switch
should
be
at
on
position)
Check
motor
switc
h
(Motor
switch
should
be
at
on
position)
C
h
e
c
k
a
lu
m
in
u
m
fi
lt
e
r
(A
lu
m
in
u
m
C
a
s
s
e
tt
e
Filter
shoul
d
b
e
washed
once
a
mont
h
a
t
normal
conditions.
)
Check
lamps(Lamps
shoul
d
b
e
firm.)
Check outlet (Outlet should be open)
Check
Carbon
Filte
r
(Carbon
filter
should
be
replaced
with
a
new
one
each
2-3
months
at
th
e
m
o
d
e
ls
w
it
h
C
a
r
b
o
n
F
il
t
e
r
a
t
n
o
r
m
a
l
conditions)
Cooker-hood does not work
Illumination Lamp does not work
Cooker-hoods air suction is weak
Cooker-hood does not direct air out
(at places without chimney)
Table 1
TECHNICAL SPECIFICATIONS
Feeding Voltage
220-2 0 V 50Hz
4
Motor Isolation Class
Isolation Class
F
CLASS I
REPLACING THE LAMPS
Disconnect the hood from mains.
*Remove the power connection of LED lamp.
*Press on the lamp with your hand to remove the
lamps.
*Remove the adhesive tape
around the lamp frame from the
body plate.
* Before placing the new LED
bulb, remove the protective foil
on the frame and stick it on its
position on the appliance body.
Replacement of Glow Bulbs
Disconnect the hood from mains. Remove the
aluminum cartridge filter.
Remove the faulty bulb and replace with a new one
with the same rating. (Lamps may burn your hand
when they are hot, wait until they are cooled off.)
In order to replace the lamp, remove the glass cover
on the lamp with an object that would not scratch the
surface of the appliance as shown in
Figure 16.
Pull down and remove the faulty lamp and replace
with a new one.
Figure 16
Summary of Contents for MEP 191 XN
Page 2: ...2 DESENHOS TÉCNICOS ...
Page 13: ...13 TECHNICAL DRAWINGS ...
