- Use this control to switch the light on independently of the fan motor, it will be lit red in this
mode.
- When the fan is in use, and the light is off, the icon will be lit white in this mode, but will turn
red if
the light is then switched on.
Fan On/Off and Speed Reduction
- Press this icon once to turn on the fan motor at speed 1. All icons will be lit white and the
light icon
will be red if already in use.
- If the motor is on speed 1, pressing and holding this icon for two seconds will turn off the fan
motor.
As above, the light control is independent of this operation.
- If the motor is higher than speed 1, this will reduce the fan speed with each press of the icon.
LED Display
- Shows the extraction mode during set up or
and the motor speeds from 1-5, and P for
Boost.
Boost Function and Speed Increase
- Press this icon once to turn on the fan motor at full power, and P will
fl
ash in the display,
- If the motor is already on speed 1-5, each press of this icon will increase the fan speed
accordingly.
- If you press and hold the icon for two seconds, the fan speed will increase to full power and
P will
fl
ash in the display.
NOTE:
Full power or Boost only operates for
fi
ve minutes maximum to conserve
energy and the fan speed will automatically drop to speed level 5 after this time.
Timer
PT
- When the fan motor is on and the Timer
icon is pressed, the icon will be lit red and the
current speed in the display will start to
fl
ash.
- The chosen speed level will remain in use for
fi
ve minutes before dropping down to the next
lowest
speed. This speed will remain in operation for two minutes before dropping down
again. This will be
repeated every two minutes unless the speed is already at level 1 and
then the fan will turn off. If
the light is already on, this will also be turned off.
- Pressing the Speed Reduction
or Speed Increase
icon during a current timer program
will
restart the countdown process again with a
fi
ve minute cycle.
- If the Timer
icon
is pressed again during a current timer program, the cycle will be
cancelled, the
icon will revert to white and the current fan speed will remain on inde
fi
nitely.
- The maximum timer program cycle is 15 minutes: 5 minutes on P and then 2 minutes each
on
speed 5 down to speed 1.
55
Summary of Contents for MET 163 X
