10
11
INTRODUCTION
To get the best out of your new appliance, please read this user guide carefully
before using it for the first time. Take particular note of the safety precautions. We
also recommend that you keep the instructions for future reference.
IMPORTANT SAFETY PRECAUTIONS
• Incorrect use of this appliance may cause personal injury and damage.
• Use for its intended purpose only. Do not use for drying towels, clothes or the
like. The manufacturer is not responsible for any injury or damage resulting from
incorrect use or handling (see also Guarantee Terms).
• For domestic use only. Not for commercial use. Do not use for heating building
sites, greenhouses, barns or the like.
• For connection to 230 V, 50 Hz only.
• Handle with care. The quartz tubes in the heating head are fragile. Avoid
subjecting to heavy impact. Do not remove the grille. If necessary to clean the
heating head inside, contact a professional.
• The appliance should be set up or mounted in accordance with the instructions
in section “Positioning of the appliance” below.
• The appliance is high powered and can emit very intense heat. Do not expose
animals or small children to direct heat from the appliance.
• The appliance must never be mounted or used in the vicinity of flammable
objects, e.g. curtains, furniture, etc. It must not be set up or mounted in wet or
damp environments (in bathrooms, by swimming pools, etc.).
• Do not use the appliance outdoors in wet weather!
• In order to reduce the risk of fire or electric shock, never use the appliance
together with an electronic timer or device which turns on and off the appliance
automatically.
• Do not cover.
• Do not cover or block the remote control receiver (remote control models only).
This will prevent the signal being received.
• Ensure that the cable does not get caught beneath the appliance, behind
shelves etc. Do not run the cable under carpets, rugs, etc. Place the cable so
that it is not possible to trip over it, and avoid wrapping it around the stand (only
models with base) or heater head.
• If use of an extension cable is required with the appliance, then the extension
cable should have a minimum rating of 10A and 2000W. If a cable reel is used,
then it should be unrolled entirely.
• Do not submerge in any form of liquid.
• Never insert your fingers, pencils or other objects through the grille. The grille
will become hot during use and must not be touched until the appliance has
cooled down.
• Switch off and allow to cool before moving or cleaning.
• Keep an eye on any children in the vicinity of the appliance when it is in use.
Children must not be allowed to use the appliance unless supervised by an
adult.
• Never try to repair the appliance yourself. If the appliance, cable or plug needs
to be repaired, it should be taken to an authorised service centre. Unauthorised
repairs or modifications will invalidate the guarantee. Please contact the store
where you bought the appliance for repairs under guarantee.
KEY TO MAIN COMPONENTS OF THE APPLIANCE
1. Heating head
2. Grille
3. Quartz tube
Model 670-206/207
4. Function indicator
5. String
Model 670-208/209/211
6. Control panel
7. Function indicator
8. On/Power button
9. Receiver for remote control
signal
10. OFF button
11. Electrical cord
12. Clip
13. Wall mounting bracket
14. Mounting screw
15. Remote control (model 670-208/209/211 only)
I. OFF button
II. On/Power button
Stand components (for models with base only:
a. Base
b. Stand, lower part
c. Screws (x2)
d. Stand, middle part
e. Stand, upper part
f. Thin rod
g. Sleeve
h. Cuff
i. Washer and screw
j. Cord holder
Tent bracket (model 670-209/211 only)
k. Curved bar
l. Bracket, front
m. Bracket, rear
n. Screws and nuts for bracket
o. Mounting screw
A wall bracket together with rawlplugs and
screws are included with the wall-mounted
model.
Certain models also have remote control and waterproof cover.
POSITIONING THE APPLIANCE
Wall-mounted model (670-206/208)
• The heater head (1) should be
at least 30cm from the ceiling,
30 cm from any side wall, and at
least 1.8m above the floor.
• Use the wall bracket supplied for
wall mounting. Do not use other
brackets or fittings.
• Screw wall bracket to wall as
illustrated. The angled section of
the bracket should face upwards.
• Hang the heater head on the wall
bracket. Mount hanging bracket
(13) at the top of the rear of the
heating head on angled part
of wall bracket. Insert retaining
screw in hole in wall bracket
base, and tighten securely.
• Check that the appliance is firmly fixed in place before using it.
Models with tent bracket (model 670-209/211)
• The heater head (1) should be at least 30cm
from the tent ceiling or parasol cover, 30 cm
from any side wall, and at least 1.8m above
the floor.
• Use the tent bracket supplied for mounting.
Do not use other brackets or fittings.
• Mount tent bracket front (l) and rear sides (m)
on a tent or parasol pole as illustrated. Use
the screws and nuts supplied (n).
• Mount curved bar (k) into socket on front of
bracket using the retaining screws supplied
(o).
UK
