background image

 16

TROUBLESHOOTING                                                                                               

             

Problem Possible 

Cause 

Corrective 

Action 

Burner won’t light  Gas pressure is low. 

 
The orifice is blocked. 
Control knob is not in “High” 
position. 

Turn tank valve “OFF” and replace 
the tank 
Clear blockage. 
Turn control knob to “High” 

Burner flame is 

low 

Gas pressure is low. 
 
The control knob is not positioned 
at “High”. 

 

The burner jet may be partially 
blocked. 
 
Outdoor temperature is less than 
40°F and tank is less than 1/4 full. 
 
Supply hose is bent or kinked. 

Turn tank valve “OFF” and replace 
the tank. 
Position the control knob at “High” 
 
 
Clear blockage. 
 
 
Use a full tank. 
 
 
Straighten the hose. 

Carbon build-up 

Build-up of carbon can accumulate 
over time. 

Wipe off before lighting. 

Thick black 

smoke 

Blockage 

in 

burner 

Remove blockage and clean 
burner inside and outside. 

 

 

 

 

1-YEAR LIMITED WARRANTY                                                                                               

The appliance has been manufactured under the highest standards of quality and 
workmanship. We warrant to the original consumer / purchaser that all aspects of this 
product will be free of defects in material and workmanship for one (1) year from the date of 
purchase. A replacement for any defective part will be supplied free of charge for installation 
by the consumer. Defects or damage caused by the use of other than genuine parts are not 
covered by this warranty .This warranty shall be effective from the date of purchase as 
shown in the purchaser’s receipt. This warranty is valid for the original consumer purchaser 
only and excludes industrial, commercial or business use of the product, product damage 
due to shipment or failure which results from alteration, product abuse, or product misuse, 
where performed by a container, service company, or consumer. We will not be responsible 
for labor charges and/or damage incurred in installation, repair or replacement, nor for 
incidental or consequential damage. This warranty gives you specific legal rights, and you 
may also have the other rights that vary from state to state. 

If problems cannot be corrected by using these methods, pleas contact 
1-855-CHANT-US (1-855-242-6887) for assistance. 

Summary of Contents for PG195H


















Reviews: