MEN NL31 User Manual Download

Page: 3 / 38

20NL31-00 E1



2019-02-13

Page 3

Contents

3.5 Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

4 Switch Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

5.1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

5.2 Updating the Switch Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Figures

Figure 1.

Front interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Figure 2.

Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Figure 3.

Product label. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Figure 4.

Power configuration and coding labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Figure 5.

Accessing the help option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Tables

Table 1.

Connector types – power supply (4-pin M12 A-coded). . . . . . . . . . . . . . . . . . .28

Table 2.

Pin assignment - power supply (4-pin M12 A-coded) . . . . . . . . . . . . . . . . . . . .28

Table 3.

Signal mnemonics – power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Table 4.

Isolation voltages (with A- or/and D-coded connectors) . . . . . . . . . . . . . . . . .28

Table 5.

Isolation voltages (with X-coded connectors) . . . . . . . . . . . . . . . . . . . . . . . . . .28

Table 6.

Connector types – 5-pin, M12, L-coded. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Table 7.

Pin assignment - power supply (5-pin M12 L-coded) . . . . . . . . . . . . . . . . . . . .29

Table 8.

Signal mnemonics – power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Table 9.

Connector types – Ethernet (4-pin, M12, D-coded) . . . . . . . . . . . . . . . . . . . . . .30

Table 10. Pin assignment – Ethernet (4-pin M12). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Table 11. Signal mnemonics – Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Table 12. Connector types – Ethernet (8-pin M12). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Table 13. Pin assignment – Ethernet (8-pin M12). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Table 14. Signal mnemonics – Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Table 15. Connector types – Ethernet M12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Table 16. Pin assignment – Ethernet (8-pin M12). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Table 17. Signal mnemonics – Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Table 18. Connector types – Q-ODC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Table 19. Pin assignment – Q-ODC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Table 20. Signal mnemonics – Q-ODC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Table 21. Power over Ethernet classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Table 22. Ethernet status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Table 23. Default switch configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Table 24. Connector types – RS232 M12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Table 25. Pin assignment – RS232 M12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Table 26. Signal mnemonics – RS232 M12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Table 27. General status LEDs at front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Summary of Contents for NL31







































Search results

Summary of Contents for NL31

Reviews:

Related manuals for NL31

Brands by name

Popular brands

MEN NL31, User Manual

Search results

Summary of Contents for NL31

Reviews:

Related manuals for NL31

Brands by name

Popular brands