background image

4

--------------------------------------------------------------------------------------------------------------------------------------------------------------

INFORMATION FOR THE USER, INSTALLER AND SERVICE ENGINEER

------------------------------------------------------------------------------------------------------------------------------------------
Special care must be taken when installing a stove such that the requirements of the Health & Safety at
Work Act are met.

Handling

Adequate facili�es must be available for loading, unloading and site handling.

Fire Cement

Some types of fire cement are caus�c and should not be allowed to come into contact with the skin. In
case of contact wash immediately with plenty of water.

PREPARATORY WORK AND SAFETY CHECKS

IMPORTANT WARNING

This stove must not be installed into a chimney that serves any other hea�ng appliance. There must not
be an extractor fan fi�ed in the same room as the stove because this can cause the stove to emit fumes
into the room.

Asbestos

This stove contains no asbestos. If there is a possibility of disturbing any asbestos in the course of
installa�on then please seek specialist guidance and use appropriate protec�ve equipment.

Metal Parts

When installing or servicing this stove care should be taken to avoid the possibility of personal injury.

CO Alarms:-

Building regula�ons require that whenever a new or replacement fixed solid fuel or wood/biomass
appliance is installed in a dwelling a carbon monoxide alarm must be fi�ed in the same room as the
appliance. Further guidance on the installa�on of the carbon monoxide alarm is available in BS EN
50292:2002 and from the alarm manufacturer’s instruc�ons.

Provision of an alarm must not be considered a subs�tute for either installing the appliance correctly or
ensuring regular servicing and maintenance of the appliance and chimney system.

Stove paint Aerosols
Paint aerosols are flammable and therefore dangerous to use around a lit stove. Be sure to allow
aerosols spray paints to dry and ven�late the room well before ligh�ng the stove. The use of any aerosol
around lit stove is dangerous and care must be take in handling aerosols.

IMPORTANT:
These instruc�ons cover the basic principles to ensure the sa�sfactory installa�on of Mendip Stoves
product :-
Ashco� Wide Model , although detail may need slight modifica�on to suit par�cular local site
condi�ons.
In all cases the installa�on must comply with current Building Regula�ons, Local Authority Byelaws and
other specifica�ons or regula�ons as they affect the installa�on of the stove. It should be noted that
the Building Regula�ons requirements may be met by adop�ng the relevant recommenda�ons given in
Bri�sh Standards BS 8303, BS EN 15287 as an alterna�ve means to achieve an equivalent level of
performance to that obtained following the guidance given in Approved Document J.

Summary of Contents for Ashcott with logstore

























Reviews: