12 EN
EN 13
english
english
7. error handling and troubleshooting
11. ec declaration of conformity
We hereby declare under our sole responsibility
that the machine designated below, placed
on the market by us and described in these
operating instructions, complies with the following
standards. This declaration loses its validity
in case of a machine modification without our
consent.
Product:
Drywall sanders
Type:
MENZER LHS 225
serial number range:
189 xxx xxx
Type:
MENZER LHS 225 VARIO
serial number range:
190 xxx xxx
relevant ec directives
2006/42/EC; (EC) No. 1907/2006 (REACH);
2011/65/EU; 2014/30/EU
applied harmonised standards
EN 60745-1; EN 60745-2-3; EN 55014-1;
EN 55014-2; EN 61000-3-2; EN 61000-3-3
MENZER GmbH
Strasse des 17. Juni 4
04425 Taucha
Germany
12. Warranty conditions
The consumer is granted a warranty with the
purchase of a MENZER electric power tool from
the BASE LINE product family.
The detailed terms of warranty can be found at:
https://www.menzer-tools.com/
service
MENZER Service
Phone: +49 (0) 342 98 74 14 15
Fax:
+49 (0) 342 98 74 14 29
E-mail:
service@menzer-tools.com
No liability for typographical errors.
Subject to technical changes.
8. Transport and storage
The machine must only be transported in the
original MENZER packaging provided. Always store
the sander in its appropriate packaging outside
the reach of children and prevent exposure to
moisture.
9. disposal
Do not dispose of electric power tools in
household waste! The devices, their accessories
and packaging must be ecologically recycled in
compliance with national requirements!
EU only: In accordance with the EU
Directive 2012/19/EU on electrical and
electronic waste, electric power tools must be
collected separately and ecologically recycled.
10. functional accessories and
peripherals
Only use original MENZER accessories matching
this particular device for optimal work results.
Y. MENZER LHS 225 accessories and spare parts
(see page *20*) – not included in the scope of
delivery:
https://www.menzer-tools.com/
en/lhs_225_lp_device
Z. MENZER industrial vacuum cleaner (see page
*20*) – not included in the scope of delivery:
https://www.menzer-tools.com/
en/industrial_vacuum_cleaners
Torsten Ceranski
Managing Director
Taucha,
11/11/2020
Problem
Possible causes
remediation
• The machine is without
function or malfunctioning.
• Mains plug is incorrectly inserted
into the mains socket.
• Mains plug is defective
• Worn carbon brushes
• Mains fuse was tripped.
• Check the plug connection; insert
the mains plug correctly into the
mains socket.
• Check mains fuse.
• Contact the MENZER repair service.
• The machine is too noisy.
• Machine vibration is
excessive.
• Velcro backing pad or abrasive
incorrectly attached.
• Filler material or substrate to be
processed is too hard.
• Attach the velcro backing pad and
abrasive securely and centrically.
• Change the rotational speed.
• Choose another abrasive. Read our
abrasive overviews or seek advice.
• Contact the MENZER repair service.
• The machine produces too
much dust.
• Insufficient extraction
performance.
• Clogged extraction pipe
• Dust bag in the industrial extractor
is full.
• Kink in the extractor hose
• Defective click-in brush ring
• Positions of the extraction openings
are not congruent.
• Clean the extraction system.
• Empty the dust bag.
• Unkink the extractor hose.
• Replace the click-in brush ring
.
• Position the extraction openings
congruently.
• Too much of the substrate is
abraded.
• The grit size of the abrasive is too
large.
• Choose a smaller grit size.
• The entire sanding area
displays a bad or sub-optimal
surface quality.
• The abrasive grit is incorrect or too
large and/or the incorrect type of
abrasive is being used
• The material or substrate to be
processed is not yet completely dry.
• The substrate is too soft and/or has
a very high filler content.
• Choose a smaller grit size and/or a
different type of abrasive. Read our
abrasive overviews or seek advice.
• Read the data sheets and
processing information provided by
the substrate manufacturer.
• Striae in the sanded area
• Backing pad not flat on the
substrate.
• Filler material too soft.
• Position the velcro backing pad
flush on the substrate.
• Choose a smaller grit size.
• Deteriorating adhesion of the
abrasive or the velcro backing
pad accessory.
• Reverse of the abrasive is worn.
• Hook & loop of the velcro layer on
the backing pad is worn.
• Replace the abrasive.
• Replace the
velcro backing pad.
• Use the backing pad cover.
Summary of Contents for LHS 225
Page 76: ......
