background image

User Manual FSK700-2 / FSK700-2SX

Chapter 1   •  Introduction

11

Confirmation signal

Signal transmitted to the fire detection control panel by the transmitting device, serving as con-
firmation of the successful activation of the transmitting device.

Variable lock

Lock that can be converted to use a new key code without replacing the tumblers.

1.11 

Standards, Guidelines, CE marking

This manual contains dated and undated references to relevant standards. These references appear 
in the appropriate sections of the manual, the titles of these standards are listed below. The latest 
version of the respective standards are in effect.

DIN 14675 / App. C

Fire detection and fire alarm systems - Design and operation

VdS 2105

Schlüsseldepots (SD) - Anforderungen an Anlagenteile

VdS 2350

Schlüsseldepots (SD) - Planung, Einbau und Instandhaltung

DIN 1053

Masonry

DIN 106

Calcium silicate units with specific properties

DIN 1045

Concrete, reinforced and prestressed concrete structures

DIN 49020

Conduit for Electrical Wiring; Screwed Steel Conduit, Plain Conduit, 
Couplers

The CE marking on the Series FSK700 Fire Brigade Key Safe is done in accordance with Directive 
2004/108/EC of the European Parliament and of the Council regarding Electromagnetic Compatib-
ility (EMC). With the CE marking, see page 38 in chapter 8.2: "EC Declaration of Conformity", the 
manufacturer confirms that the product conforms to EMC Directive 2004/108/EC.

1.12 

Warranty

All parts of the Series FSK700 Fire Brigade Key Safe by MEP are manufactured with highest pre-
cision and utmost care. Nonetheless, the occurrence of malfunctions during operation cannot be 
ruled out entirely. To register a complaint, please contact the company responsible for installation 
of your system.

While the warranty period is in effect, all parts that become defective because of a demonstrable 
flaw in their manufacture or in material will be either replaced or repaired free of charge. In such 
cases, the time period of the original warranty will not be extended, nor will a new warranty period 
be set for the replaced or repaired parts. All further claims are excluded, especially those regarding 
reductions of the purchase price, cancellation of contract, compensatory damages or replacement 
due to secondary damages of any type. Beyond these regulations, the current regulations of the 
"General Terms of Delivery" that are issued by the Austrian Electrical and Electronics Industry 
Association are in effect.

HB_FSK700_1020_9161690_Englisch_D.odt / 1022 D / AN9161690
ZN62163/38/11

11

Summary of Contents for Fire Brigade Key FSK700 Series







































Reviews: