background image

To configure physical link settings on the Ethernet ports, click 

Local status > Ethernet configuration

. You can 

enable half duplex, full duplex, and auto-negotiation, as well as set 10- or 100-Mbps data rates. 

Regulatory 

 

FCC Compliance Statement

 

 

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 

Party issuing 

Supplier’s

 Declaration of Conformity

 

Cisco Meraki 

500 Terry A. Francois Blvd.  San 
Francisco, CA 
94158 
USA 

compliance@meraki.com 

 

 

FCC Interference Statement

 

 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant  to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful  interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency  energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference  to radio communications. However, there is no guarantee that 
interference will not occur in a particular  installation. If this equipment does cause harmful 
interference to radio or television reception, which can  be determined by turning the equipment off 
and on, the user is encouraged to correct the interference by  one of the following measures: 
 
Reorient or relocate the receiving antenna. 
  
Increase the separation between the equipment and receiver. 
 
Connect the equipment into an outlet on a circuit different from which the receiver is connected. 
 
Consult the dealer or an experienced radio/TV technician for help. 
 

FCC Caution

 

 

Any changes or modifications no expressly approved by Cisco could void the 

user’s

 authority to operate 

this equipment. This Transmitter must not be co-located or operation in conjunction with any other 
antenna  or  transmitter. 
 

FCC Radiation Exposure Statement

 

Summary of Contents for MG21












Reviews: