Mercedes-Benz 2016 Command Operating Instructions Manual Download

Page: 118 / 222

De-authorizing (disconnecting) a

mobile phone

Mercedes-Benz USA, LLC recommends de-

authorization in COMAND and on the mobile

phone. Subsequent authorization may other-

wise fail.

To call up the telephone menu: press the

button.

To show the menu bar: slide

the con-

troller.

To select

Connect Device

: turn and press

the controller.

To highlight the desired mobile phone in the

device list: turn the controller.

To select

: slide

the controller.

To select

Deauthorize

: turn and press the

controller.

A prompt appears, asking whether you

really wish to de-authorize this device.

To select

Yes

: turn and press the controller.

The mobile phone is de-authorized.

Before re-authorizing the mobile phone,

you should also delete the device name

Bluetooth

from your mobile phone's Blue-

tooth

list.

Displaying connection details

To call up the telephone menu: press the

button.

To switch to the menu bar in the telephone

menu: slide

the controller.

To select

Connect Device

: turn and press

the controller.

To highlight the desired mobile phone in the

device list: turn the controller.

To select

: slide

the controller.

To select

Details

: turn and press the con-

troller.

The following information concerning the

selected mobile phone is shown:

Bluetooth

device name

Bluetooth

address

Availability status (shown after a new

search)

Authorization status

To close the detailed display: slide

the controller.

Reception and transmission volume

Once the mobile phone has been authorized,

you can optimize the transmission and recep-

tion volume settings. To find out about the

best possible settings for your mobile phone,

visit www.mercedes-benz-mobile.com.
Or call the Mercedes-Benz Customer Assis-

tance Center at 1-800-FOR-MERCedes

(1-800-367-6372) (USA) or Customer Rela-

tions at 1-800-387-0100 (Canada).

To call up the telephone menu: press the

button.

To switch to the menu bar: slide

the

controller.

To select

Connect Device

: turn and press

the controller.

The device list appears.

To highlight the desired mobile phone in the

device list: turn the controller.

To select

: slide

the controller.

To select

Reception Volume

Trans‐

mission Volume

: turn and press the con-

troller.

To select a volume setting: turn the con-

troller.

To accept changes: press the controller.

116

Reception and transmission volume

Teleph

one

Summary of Contents for 2016 Command































































































































































































































Search results

Summary of Contents for 2016 Command

Reviews:

Related manuals for 2016 Command

Brands by name

Popular brands

Mercedes-Benz 2016 Command, Operating Instructions Manual

Search results

Summary of Contents for 2016 Command

Reviews:

Related manuals for 2016 Command

Brands by name

Popular brands