Mercedes-Benz 2016 Command Operating Instructions Manual Download

Page: 79 / 222

To select a POI category or

Other

: turn and

press the controller.

After selecting one of the eight POI cate-

gories, available POIs are displayed:

along the route

in the vicinity

COMAND first searches for destinations on

the route. The search for destinations is

then initiated in the area around the current

vehicle position.

After selecting

Other

, select one of the

destination entry options.

Selection

Step

Address

Entry

Enter a destination by

address (

page 67).

Keyword

Select a destination by

means of a keyword

search (

page 70).

From Previ‐

ous Destina‐

tions

Select a destination

from the list of last des-

tinations (

page 72).

From Con‐

tacts

Select a contact from

the address book as

the destination

(

page 72).

From POIs

Select a point of inter-

est (

page 72).

Using Map

Enter a destination

using the map

(

page 75).

From Memory

Card

Select a personal POI

(

page 82).

From

Mercedes-

Benz Apps

Enter a destination

from Mercedes-Benz

Apps (

page 79).

Using Geo-

Coordinates

Enter a destination

using the geo-coordi-

nates (

page 79).

To select a POI: turn the controller and

press to confirm.

After selecting a POI or entering a destina-

tion, the address of the intermediate des-

tination is displayed.
After entering a destination using the map,

the address entry menu is displayed.

Start

is highlighted.

To call up a map: select

Map

by turning and

pressing the controller.

You can move the map and select the des-

tination.

To make a call: select

Call

If the intermediate destination has a tele-

phone number and a mobile phone is con-

nected to COMAND (

page 112), the call

is connected.

To load data from the Internet: select

www

If an Internet address is available, data is

loaded from the Internet.

Destination entry

Navigation

Summary of Contents for 2016 Command































































































































































































































Search results

Summary of Contents for 2016 Command

Reviews:

Related manuals for 2016 Command

Brands by name

Popular brands

Mercedes-Benz 2016 Command, Operating Instructions Manual

Search results

Summary of Contents for 2016 Command

Reviews:

Related manuals for 2016 Command

Brands by name

Popular brands