Mercedes-Benz Command Operating Instructions Manual Download

Page: 115 / 226

Call disconnection while the vehicle is

in motion

A call may be disconnected if:

there is insufficient network coverage in

certain areas.

you move from one transmitter/receiver

area (cell) into another and no channels are

free.

you use a SIM card that is not compatible

with the network available.

Operating options

You can operate the telephone by:

using the controller by turning, pressing,

sliding

using the touchpad (

page 25)

using the

button on the mul-

tifunction steering wheel

using the Voice Control System (see the

separate operating instructions)

Unless stated otherwise, the descriptions and

illustrations in this section refer to COMAND.

Function restrictions

You may have to wait before using telephony

via COMAND in the following situations:

when the mobile phone is switched off

if Bluetooth

is switched off on the mobile

phone

if the mobile phone has not logged on to a

mobile phone network

if the Bluetooth

function is switched off in

COMAND

The telephone automatically tries to log on to

a network. If no network is available, you may

not be able to make a "911" emergency call.

If you attempt to make an outgoing call, the

No Service

message will appear for a short

while.

Telephone menu

Mobile phone network provider

;

Signal strength of the mobile phone net-

work

Receiver icon

Telephone menu character bar

Bluetooth

device name of the currently

connected mobile phone

To enter characters using the touchpad

To display the phone book

Symbols

and

are not shown until

after a mobile phone has been connected to

COMAND. The symbols depend on your

mobile phone and your mobile phone network

provider. Further information on connecting a

mobile phone (

page 114).

Symbol

;

shows the current signal strength

of the mobile phone network. If all bars are

filled, you have optimum reception.
If the bars are not filled, you have very poor

reception or no reception at all.

Receiver icon shows whether a call is

active/being connected

or not

Calls up the telephone menu

To show the main function bar: slide

the controller.

To select

Phone

: turn and press the con-

troller.

The telephone menu is displayed.

Showing the menu bar

Slide

the controller.

If the mobile phone connected supports the

MAP Bluetooth

profile (Message Access

Telephone menu

113

Telep

hone

Summary of Contents for Command



































































































































































































































Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands

Mercedes-Benz Command, Operating Instructions Manual

Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands