Mercedes-Benz Command Operating Instructions Manual Download

Page: 16 / 226

Operating safety

Important safety notes

WARNING

Modifications to electronic components, their

software as well as wiring can impair their

function and/or the function of other net-

worked components. In particular, systems

relevant to safety could also be affected. As a

result, these may no longer function as inten-

ded and/or jeopardize the operating safety of

the vehicle. There is an increased risk of an

accident and injury.
Never tamper with the wiring as well as elec-

tronic components or their software. You

should have all work to electrical and elec-

tronic equipment carried out at a qualified

specialist workshop.

If you make any changes to the vehicle elec-

tronics, the general operating permit is ren-

dered invalid.

WARNING

If you operate information systems and com-

munication equipment integrated in the vehi-

cle while driving, you will be distracted from

traffic conditions. You could also lose control

of the vehicle. There is a risk of an accident.
Only operate the equipment when the traffic

situation permits. If you are not sure that this

is possible, park the vehicle paying attention

to traffic conditions and operate the equip-

ment when the vehicle is stationary.

You must observe the legal requirements for

the country in which you are currently driving

when operating COMAND.
COMAND calculates the route to the destina-

tion without taking account of the following,

for example:

traffic lights

stop and yield signs

merging lanes

parking or stopping in a no parking/no

stopping zone

other road and traffic rules and regulations

narrow bridges

COMAND can give incorrect navigation com-

mands if the actual street/traffic situation

does not correspond with the digital map's

data. Digital maps do not cover all areas nor

all routes in an area. For example, a route may

have been diverted or the direction of a one-

way street may have changed.
For this reason, you must always observe

road and traffic rules and regulations during

your journey. Road and traffic rules and reg-

ulations always have priority over the sys-

tem's driving recommendations.
Navigation announcements are intended to

direct you while driving without diverting your

attention from the road and driving.
Please always use this feature instead of con-

sulting the map display for directions. Look-

ing at the icons or map display can distract

you from traffic conditions and driving, and

increase the risk of an accident.
Bear in mind that at a speed of only 30 mph

(approximately 50 km/h) your vehicle covers

a distance of 44 feet (approximately 14 m)

per second.
This equipment complies with FCC radiation

exposure limits set forth for uncontrolled

equipment and meets the FCC radio fre-

quency (RF) Exposure Guidelines in Supple-

ment C to OET65.
This equipment has very low levels of RF

energy that is deemed to comply without

maximum permissive exposure evaluation

(MPE). But it is desirable that it should be

installed and operated with at least 8inches

(20cm) and more between the radiator and a

person's body (excluding extremities: hands,

wrists, feet and legs.)

Introduction

Summary of Contents for Command



































































































































































































































Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands

Mercedes-Benz Command, Operating Instructions Manual

Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands