Mercedes-Benz Command Operating Instructions Manual Download

Page: 218 / 226

Your COMAND equipment

These operating instructions describe all the

standard and optional equipment for your

COMAND system, as available at the time of

going to print. Country-specific differences

are possible. Please note that your COMAND

system may not be equipped with all the fea-

tures described.

Weather forecasts

Introduction

This function is currently not available for

Canada.
For the reception of weather forecasts via

satellite radio, you will need a SIRIUS XM Sat-

ellite Weather subscription.
If the message:

Call SIRIUS to activate

system at: 888-539-7474 ESN:

SIRIUS ID

appears along with the ID number

of the SIRIUS device, you will need to have the

weather service activated first.

To select

Call

Cancel

: turn and press

the controller.

If a mobile phone is connected to COMAND

(

page 114), the call will connect to a SIR-

IUS service employee after selecting

Call

The ID number of the SIRIUS device will be

transferred to the telephone display.

This will be followed by instructions from

the service employee.

COMAND can receive weather forecasts via

satellite radio for the entire USA (including

Alaska and Hawaii).
The received weather data can be displayed

as an information chart (daily forecast, five-

day forecast, detailed information) or on the

weather map.
The weather data received from a weather

station is stored in COMAND for one hour. It

can therefore be displayed again immediately

after restarting the engine (for example after

refueling).

Depending on which scale has been selected,

the weather map can display the following

weather data with symbols:

rain radar

storm characteristics

high and low-pressure areas, weather

fronts

course of tropical cyclones (hurricanes,

typhoons)

gale warnings

wind direction and speeds

The rain radar cannot be displayed for

Alaska, Hawaii and Puerto Rico.

Hurricane: term used to describe the trop-

ical cyclones that primarily develop in the

Atlantic, North Pacific and South Pacific

oceans. The wind speeds are above 74 mph

(118 km/h). Five categories are used to

classify the strength of a hurricane.
Typhoon: term used to describe a tropical

cyclone that develops in the northwestern

Pacific. The wind speeds are in the category

of a hurricane.

Switching the SIRIUS Weather display

on/off

Activating

To show the main function bar: slide

the controller.

To select

: turn and press the controller.

The menu for selecting internet applica-

tions appears.

216

Weather forecasts

SIRIU

Weather

Summary of Contents for Command



































































































































































































































Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands

Mercedes-Benz Command, Operating Instructions Manual

Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands