Mercedes-Benz Command Operating Instructions Manual Download

Page: 64 / 226

To switch to navigation mode: slide

the controller.

To select

Navi

: turn and press the control-

ler.

The map displays the current vehicle posi-

tion or the navigation menu appears.

If the navigation menu appears, press the

controller.

The map shows the vehicle's current posi-

tion.

To show the menu: slide

the control-

ler.

To select

Options

: turn and press the con-

troller.

Select

Settings

Select an option.

Switch the option on

or off

Announce

Street

Names

COMAND announces the

names of the streets to which

the impending change of

direction will lead.
The function is not available

in all countries.

Audio

Fadeout

The volume of an active

media source is automati-

cally reduced during a navi-

gation announcement.

Gas on

Reserve

Function activated: once the

reserve fuel tank level is

reached, a message appears

to help you start a gas station

search.

Atten‐

tion

Assist

Function activated: if ATTEN-

TION ASSIST displays a warn-

ing in the multifunction dis-

play, a message appears in

the COMAND display when

driving on a highway. This can

help you start a rest stop

search.
For further information on

ATTENTION ASSIST, see the

vehicle Operator's Manual.

Using car pool lanes

You can include carpool lanes (HOV or car

sharing lanes) in the route calculation.
If you use HOV or carpool lanes, please

observe the applicable laws as well as the

local and time limitation conditions.
Carpool lanes may only be used under certain

conditions. They can normally be used when

there are two people in the vehicle. However,

there are also carpool lanes which can only be

used when there are three or more people in

the vehicle. In California, lone drivers can use

a carpool lane if their vehicle's emission level

or fuel consumption is below a fixed thresh-

old.
Carpool lanes may be reserved for specific

times (e.g. during the peak period).
Carpool lanes are indicated by a diamond

symbol on specific road signs and on the road

surface. The road signs may also include the

designation CARPOOL. The lanes are

arranged as a separate lane next to the others

or are built as a physically separate lane.
Depending on the setting under

Use Car‐

pool Lanes

, COMAND uses carpool lanes

when calculating the route. During route guid-

ance, visual and audible driving directions

provide guidance into and out of carpool

lanes.

To switch to navigation mode: slide

the controller.

To select

Navi

: turn and press the control-

ler.

The map displays the current vehicle posi-

tion or the navigation menu appears.

If the navigation menu appears, press the

controller.

The map shows the vehicle's current posi-

tion.

To show the menu: slide

the control-

ler.

To select

Options

: turn and press the con-

troller.

Select

Route Settings

Basic settings

Navig

atio

Summary of Contents for Command



































































































































































































































Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands

Mercedes-Benz Command, Operating Instructions Manual

Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands