Mercedes-Benz Command Operating Instructions Manual Download

Page: 83 / 226

You can save the imported destinations and

routes as personal POIs and routes

(

page 79).

When importing routes, please note:

The Mercedes-Benz Apps may generate a

route based on a different map from the

one used by COMAND. Points on the route

may therefore be situated off the digital

roads. For this reason an imported route

commenced in COMAND may deviate from

the original route from the Mercedes-Benz

Apps.

The Mercedes-Benz Apps minimize the

number of route points offered. For this

reason an imported route commenced in

COMAND may deviate from the original

route from the Mercedes-Benz Apps.

Selecting and editing personal POIs

and routes

Selecting

The example shows a personal POI.

Insert the SD memory card (

page 184).

To switch to navigation mode: slide

the controller.

To select

Navi

: turn and press the control-

ler.

The map displays the current vehicle posi-

tion or the navigation menu appears.

If the navigation menu appears, press the

controller.

The map shows the vehicle's current posi-

tion.

To show the menu: slide

the control-

ler.

To select

Destination

: turn and press the

controller.

Select

From Memory Card

The menu displays the categories available

on the SD memory card.

To select a category or

Personal Routes

turn and press the controller.

The available personal POIs or route entries

are displayed.

Select personal POI or personal route.

The address of the personal POI appears or

the personal route is displayed in the map.

If a large number of entries are stored, a reg-

ister for quick selection appears. Personal

POIs and routes can be saved and sorted with

different character sets (e.g. Latin, Cyrillic,

Arabic).

To select a register: slide

the con-

troller.

To select a character: turn and press the

controller.

To select a character set for sorting:

slide

the controller to select

Press the controller.

The available character sets are displayed.

The

dot indicates the current setting.

Turn and press the controller.

Editing

The example shows a personal route.

Select personal POI or personal route

(

page 81).

Personal POIs and routes

avigation

Summary of Contents for Command



































































































































































































































Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands

Mercedes-Benz Command, Operating Instructions Manual

Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands