Mercedes-Benz Command Operating Instructions Manual Download

Page: 95 / 226

You can have the traffic report relevant to a

traffic icon shown.

To select

Details

: turn and press the con-

troller.

The report shows the following information:

State/province, road and display of the

affected direction

Section of the road to which the traffic

report applies

Traffic icon and traffic report

To close the detailed display: press the

button.

Displaying reports on the route

The function is only available while route guid-

ance is active. It shows the available traffic

reports affecting the current route.
If there are no reports for the route or the

function is not supported in the selected lan-

guage: the

Messages On Route

menu item is

gray and cannot be selected.

To switch to navigation mode: slide

the controller.

To select

Navi

: turn and press the control-

ler.

The map displays the current vehicle posi-

tion or the navigation menu appears.

If the navigation menu appears, press the

controller.

The map shows the vehicle's current posi-

tion.

To show the menu: slide

the control-

ler.

To select

Traffic

: turn and press the con-

troller.

To select

Messages On Route

: turn and

press the controller.

The traffic report window appears. Several

traffic reports may be available for the cal-

culated route, marked for example by 1/3.
The report shows the following information:

State/province, road and display of the

affected direction

Section of the road to which the traffic

report applies

Traffic icon and traffic report

To display the next/previous traffic

report: turn the controller.

To close the display: press the

but-

ton.

Displaying all traffic reports

Real-time traffic reports

avigation

Summary of Contents for Command



































































































































































































































Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands

Mercedes-Benz Command, Operating Instructions Manual

Search results

Summary of Contents for Command

Reviews:

Related manuals for Command

Brands by name

Popular brands