27
24
26
22
31
32
30
28
23
25
29
33
4m Capping Felt QTY 1
PI-01-0020
P 2
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-
driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
LOCATION FOR YOUR GARDEN BUILDING
A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,
annual treatment and to allow air flow around the building.
Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing
damage to the building.
TIMBER
As with all natural materials, timber can be affected during various weather conditions. For the duration of heavy
or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during
excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be
helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine
and sheltered as much as possible during rain or snow.
Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent
the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.
Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-
ment to prevent water ingress
Pressure Treated buildings - Require a waterproof treatment to prevent water ingress
Log Cabins - Are supplied untreated and require a preservative and waterproofing treatment.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on firm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding
should overlap the base, creating a run off for water. It is also recommended that the floor be at least 25mm above
the surrounding ground level to avoid flooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or
using this product.
01DTPRMSHPN1206DDOP-V1
Overall Dimensions:
Width = 3566mm
Depth = 1885mm
Height = 2170mm
Base Dimensions:
Width = 3506mm
Depth = 1753mm
Please retain product label and instructions for future reference
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
5
6
Roof QTY 2
AI-S21MBPR1771X1874-V1
Back Panel QTY 2
AI-S21SHPP1418X1774-V1
Side Panel QTY 2
AI-S21SHPPTOV1760X1753-V1
2
3
4
1
Window Panel QTY 1
AI-01S21SH1LFW1418X2079-V1
Door Panel QTY 1
AI-01S21SHDD1418X2079-V1
Door QTY 2
AI-S21FBMBZBD551X1742-V1
Floor QTY 2
AI-R11MBF1753X1753-V1
10
9
Right Gable Top QTY 1
AI-S21SHPGTR1760X342-V
1
Left Gable Top QTY 1
AI-S21SHPGTL1760X342-V1
Framed Window QTY 1
AI-FW1000X540-V1
Fascias 12x90x1898mm QTY 2
S1290-1898MM
11
Door Block 27x44x160mm QTY 4
F2744-160MM
12
Ridge Bar 27x70x1715mm QTY 2
F2770-1715MM
13
14
Eaves Framing 28x28x1771mm QTY 4
FS2828-1771MM
15
Door Beading Strips 12x40x1686mm QTY 2
S1240-1686MM
16
Door Cover Trims 12x56x860mm QTY 1
S1256-860MM
18
Window Cover Trim 12x56x1038mm QTY 1
S1256-1038MM
19
Cover Trims 12x56x1770mm QTY 4
S1256-1770MM
20
Cover Trims 12x5x2072mm QTY 4
S1256-2072MM
21
Fascias 12x90x1771mm QTY 4
S1290-1771MM
U-Channel QTY 1
PI-07-0013
Corner Brace QTY 2
PI-07-0012
Green Felt QTY 1
PI-01-0016
Butt Hinge QTY 2
PI-07-0066
T-Hinge QTY 6
PI-07-0021
Lock Hasp QTY 1
PI-07-0221
Turn Button QTY 4
PI-07-0034
Casement Stay QTY 1
PI-07-0007
Padlock QTY 1
PI-07-0222
17
Door Cover Trims 12x56x820mm QTY 1
S1256-820MM
7
8
2079mm Front Panel QTY 1
AI-S21SHPPTF594X2079-V1
1774mm Back Panel QTY 1
AI-S21SHPP594X1774-V1
