background image

Felt Tacks x257

70mm Screw x92

Felt

Nail Bag

40mm Screw x564

30mm Screw x126

25

26

27

28

29

30

31

32

33

10mm Screw x4

Pre-assembly

*Please note: 

Each board interlocks at

either end in a staggered pattern.

Before securing ensure that the boards

are fitted properly in their respective

tongues and grooves.

70mm Bolt Set x16

*All components for the Windows and Doors are 

shown in the Windows and Doors instruction packs.

P 3

Please retain product label and instructions for future reference

Veranda Post - 70x70x2001mm

F7070-2001 (Notched)

Fascia - 16x120x1601mm QTY 4 

S16120-1601 (Angled)

Fascia - 16x120x4036mm QTY 2 

S16120-4036

Eaves Frame - 27x44x4000mm QTY 2 

F2744-4000

Roof Board - 16x121x1600mm QTY 74 

MB16-C-1600

Floor Board - 16x121x1862mm QTY 18

MB16-C-1862

Floor Board - 16x121x2748m QTY 18

MB16-C-2748

Bearer - 44x44x2804mm QTY 2 

F4444-2804-PT

Bearer  - 44x44x3720mm QTY 12 

F4444-3720-PT

35

39

Storm Brace - 27x44x200mm QTY 8

F2744-200

Veranda Board - 16x120x880mm QTY 14 

SR16120-880

Log Board  - 28x120x2220mm 

LB28-AD-2220

36

38

Post Plate

Closure Trim - 16x28x2400mm (approx length) QTY 14

S1628-2400

34

37

Roof Spacers QTY 5

PI-07-0208 (20x100x2mm)

40

Summary of Contents for 0628LOG131-V4
















Reviews: