mcr WIP PRO
multi-blade fire damper
„
MERCOR” S.A. –
All rights reserved to modifications without prior notice
24/25
7. TRANSPORT & STORAGE CONDITIONS
_______________________________
The fire dampers are packed in cardboard boxes or placed on pallets. The fire dampers are protected against damage
with plastic film or another cover type. The fire dampers may be transported on any vehicle, which will assure
protection from weather. The fire dampers loaded on the vehicle shall be secured from shifting in transit. Before
installing the fire dampers, visually inspect each unit. Do not handle the fire damper by holding the connection cable,
or put the damper on its control-release mechanism. Do not strike or drop the fire damper. When handling and
installing, place the fire damper on casing sides or edges. Store the fire dampers in sheltered rooms protected from
outdoor elements. If the fire dampers are stored on the ground, place them on washers to prevent damage.
8. MAINTENANCE AND SERVICING _________________________________
The equipment from
„
Mercor
”
S.A. requires periodic technical inspection and maintenance at least every 12 months
throughout its operating life, i.e. during the warranty and post-warranty period. Inspection and maintenance may only
be carried out by the manufacturer or contractors authorised by
„
Mercor
”
S.A. to service its products.
The obligation to carry our regular service inspections of fire protection devices results from the § 3 Section 3 of the
Regulation by the Minister of Internal Affairs and Administration of 7 June 2010 on fire protection of buildings, other
civil structures and areas (Dz. U. 2010, no. 109 item 719).
Do these recommended actions in the inspection intervals:
Check the electrical connections, especially for all mechanical damage.
Verify the power supply values for the equipment with the following tolerances:
24 V ±10% for electric actuators
24 V ±2% for electromagnetic triggers
230 V ±10% for electric actuators
230 V ±2% for electromagnetic triggers
Check the device casing, especially for mechanical damage.
Check for any obstructions to proper operation of the equipment.
To facilitate the activities under service inspection, servicing and warranty claim response, e.g. visual inspection or
repairs, the equipment user/operator shall provide physical access to the equipment by removing thermal insulation,
suspended ceiling, and other installations, as required and applicable to warrant unobstructed access.
Inspection ports, e.g. type mcr KRW, are recommended for the equipment installed in ducts.
In the case of roof mounted equipment, provide access to the area (via ladders or elevated platforms).
Refer all matters related to technical inspection, maintenance and servicing of this equipment to the
„
Mercor
”
S.A.
Service Department, serwis@mercor.com.pl, tel. +48 58 341 42 45 ext. 170, fax: +48 58 341 39 85, from 8 AM to 4
PM (Mo-Fri).
9. WARRANTY TERMS & CONDITIONS ______________________________
1.
“MERCOR” SA grants 12 months of warranty for the equipment quality from the date of purchase, unless the
sales contract states otherwise.
2.
Submit each warranty claim to “MERCOR” SA in 7 days from the date of discovery of a warranty eligible defect
3.
Submit warranty claims by calling at: tel. +48 58 341 42 45, by fax: +48 58 341 39 85, by e-mail:
reklamacje@mercor.com.pl or by traditional mail: “MERCOR” SA, ul. Grzegorza z Sanoka 2, 80-408 Gdańsk,
Poland.
4.
If physical defects of equipment are found during the warranty period, “MERCOR” SA warrants and represents
to remove them in shortest possible time from serving the written warranty claim with the proof of purchase or
sales contract, subject to Item 10.
5.
“MERCOR” SA has the right to extend the time of repair if the defect removal is complicated or requires
purchase of custom components or spare parts.
6.
The warranty liability only covers all defects arising from causes present in the equipment at the date of sale.
7.
Defects caused by improper operation or otherwise as listed in Item 10 herein, the buyer / warranty beneficiary
will be charged with the costs of their removal.
8.
Condition for rectifying defects is that the applicant makes the site/localisation where devices are installed
available, in particular, ensuring: the lift in the case of devices mounted at a height above 3m, free access to
the rooms where the devices were installed and necessary revisions, dismantling thermal insulation,
disassembling suspended ceilings, disassembling other installations, if they prevent free access to the device.
9.
If the device can not be repaired at the place of its installation, "MERCOR" SA reserves the necessity of its
disassembly, possible delivery to the address indicated by "MERCOR" SA and re-assembly. The cost of this
operation lies with the buyer / holder of the guarantee.
10. The warranty does not cover:
