background image

 

Mercury Security © 2017 

MS-ICS 

DOC  10107-0053 

REV 1.02 

 Page   3 

 

 

 

MS-ICS to MS-ACS 

TB2 

– 2-wire RS-485 

 

The 34-conductor ribbon cable is non-standard.  Do use a floppy disk drive cable.  

 

IMPORTANT NOTE!

  Install the termination jumper (MS-ICS jumper J8), ONLY on the panel at each end 

of the RS-485 bus.  Failure to do so will compromise the proper operation of the communication channel! 

6.  Memory and Real Time Clock Backup Battery: 

The static RAM and the real time clock are backed up by a lithium battery when input power is removed.  This 
battery should be replaced annually.  If data in the static RAM is determined to be corrupt after power up, all 
data,  including  flash  memory,  is  considered  invalid  and  is  erased.    All  configuration  data  must  be  re-
downloaded.  Remove the insulator from the battery holder after installation.  Battery type: BR2325, BR2330, 
or CR2330. 

7.  Status LEDs:  

Power-up

:  All LED's

 OFF. 

Initialization:

  LED's 1 through 6 are sequenced during initialization.  LED's 1, 3, and 5 are turned ON for 

approximately 1.5 seconds after the hardware initialization has completed, then the application code is 
initialized.  The amount of time the application takes to initialize depends on the size of the database, about 3 
seconds without a card database.  Each 10,000 cards will add about 3 seconds to the application initialization.  
When LED's 1 through 4 flash at the same time, data is being read from or written to flash memory, do not 
cycle power when in this state.  If the sequence stops or repeats, perform the bulk erase procedure, see 
section 8. 

Running: 

LED 

DESCRIPTION 

Off-Line / On-Line and Battery Status 

  Off-Line = 20% ON, On-Line = 80% ON 
  Double Flash if Battery is Low 

Host Communication Activity (Ethernet or Serial Port 1) 

Port 2 Communication Activity 

Port 3 Communication Activity 

Reserved for future use 

Reserved for future use 

D7 

Host Communication (Ethernet Port 0) 

YEL 

On-board Ethernet Speed: OFF = 10Mb/S, ON = 100Mb/S (Yellow LED) 

GRN 

OFF = No Link, ON = Good Link (Green LED), Flashing = Ethernet Activity 

J1

J5

J1 of MS-ICS

34-CONDUCTOR

RIBBON CABLE

SEE NOTE BELOW

J5 OF MS-ACS

KEY

KEY

GND

TR+
TR-

TB2

To serial I/O Devices

4

1

J8

Summary of Contents for MS-ICS






Reviews: