Merlin Hobbies Knife Loop Yak 3D Instruction Manual Download | Manualshive

Page: 10 / 13

background image

10

Done.

Install the Control Surfaces and Rudder

Most of the control surfaces have been pre slotted. If you find that hinge strips do not go in or are difficult
to install, use a hobby knife to open them up.

Drill a 3/32” hole in each slot to allow CA to wick better into the hinges. Insert the hinge strips keeping

them centered in the opening and carefully align the control surface. Add six drops of Thin CA to each
side of each hinge strip. Allow the CA to cure slowly. After the CA has cured, move the control surfaces
several times to make sure they are easy to move.

Install the Servos

Trim the covering to open the servo openings in the belly and the tail of the fuselage.
And install servos in all.

«
...
8
9
10
11
12
...
»

Summary of Contents for Knife Loop Yak 3D














Reviews:

No comments

Related manuals for Knife Loop Yak 3D

Brand: Hacker Pages: 8

Brand: B Pages: 2

Techno Tiles TT Castle

Brand: The Learning Journey Pages: 386

Branchline Class 03

Brand: Bachmann Pages: 3

BUILD & REBUILD 10660

Brand: LEGO Pages: 24

Brand: Dromida Pages: 4

Brand: TILLIG BAHN Pages: 4

Brand: bewello Pages: 12

Brand: QABA Pages: 10

Junior Fly Ball

Brand: Amewi Pages: 8

Brand: Lionel Pages: 12

Pelican Aileron Wing

Brand: CRASHTESTHOBBY.COM Pages: 7

Brand: marklin Pages: 24

Mooove n Count Cow

Brand: VTech Pages: 9

Brand: NICESKY Pages: 8

Barbie TV News Anchor

Brand: KIDdesigns Pages: 2

Brand: Kiddery Toys Pages: 11

Brand: marklin Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands