background image

23

Warranty

Limited warranty

Merlin Garage Openers Limited warrants to the original purchaser (“the Buyer”) that the 
controller (“the Unit”) sold under this warranty will be free from defects in materials and 
workmanship for a period of 24 months from date of purchase. Accordingly if the Unit 
fails due to defects in materials or workmanship within the warranty period Merlin Garage 
Openers Limited will, provided the defective part or Unit is returned freight and insurance 
prepaid and well packaged to the nearest address listed in this manual, undertake to repair 
or, at its option replace, any defective part or Unit and return it to the Buyer at no cost. 
Repairs  and  replacement  parts  are  warranted  for  the  remaining  portion  of  the  original 
warranty period. 

Limitations

It expressly excludes any batteries and malfunctions or defects to the Unit or its operation 
due to any of the following:
A  

Failure to observe installation, adjustment, maintenance or operating instructions 
provided with the Unit;

B  

Incorrect  installation,  operation  or  adjustment  of  products  to  which  the  Unit  is 
fitted;

C  

Connection to any load outside the specifications set out in the owner’s manual;

D  

Any modification or repair to the Unit carried by a person not authorised to do so 
by Merlin Garage Openers Limited;

E  

Radio or any other electrical or electronic interference;

F  

Faulty or unsuitable electrical wiring of the building to which the Unit is attached;

G  

Faulty or flat batteries in the remote control transmitter;

H  

Where  the  defect  is  due  to:  conditions  other  than  normal  domestic  use  or  dirt, 
misuse, neglect, fire, accident, electrical storm or other act of God.

This warranty is void if the labelling has been altered, defaced or moved. The liability of the 
Distributor for any loss or damage or injury arising directly or indirectly from any defect in 
the goods supplied is limited to the replacement or repair of such goods or to damages 
not exceeding the invoice value of such goods at the option of Merlin Garage Openers 
Limited.

Future Modifications

Merlin Garage Openers Limited may modify any existing or future model of the Unit without 
the obligation to incorporate these modifications into Units already manufactured or into 
the Unit to which this warranty applies.

General

This  warranty  is  the  only  Warranty  made  by  Merlin  Garage  Openers  Limited.  All  other 
warranties,  representations  and  conditions  of  any  kind,  express  or  implied,  are  hereby 
excluded. This warranty does not deprive the Buyer of any rights conferred upon them by 
any applicable law or statute in their country of purchase. Proof of date of purchase may 
be required when making a claim under warranty. In the event that the Buyer is unable to 
provide adequate proof of purchase the date of warranty will apply from date of shipment 
from the Distributor to the Reseller.

NOTE

  Merlin requests that you attach your sales docket or invoice to this manual to enable 

you to establish the date of purchase in the unlikely event of service being required.

Summary of Contents for G715D





























Reviews: