background image

G715

D

 May 05

8

exactly parallel to the gate. The edge of the plate should be 40 mm from the face of the 
gate.

Position the foundation plate correct distance from the ends of the gate

The foundation plate must be positioned to allow the gate to move fully past the opening.
If the supplied limit actuating plates are attached to the rack with no modification then the 
gate must extend past the foundation plate as per the measurements shown.

Position the drive on the foundation plate

Remove the cover from the drive and place it on the foundation plate.
Centre the mounting bolts in the drive’s mounting slots.
Fit 2-mm thick spacer shims under the drive – these will be removed aftereards.
Tighten the four bolts ensuring that the drive is parallel to the gate
Operate the manual release clutch, using the key provided, pulling the lever fully out.

Fix the rack to the gate

With  the  clutch  released, 
slide the rack over the pinion 
gear. Attach one end of the 
rack  to  the  gate,  then  slide 
the  gate  along,  attaching 
each  point  of  the  rack  as  it 
passes the pinion.
Ensure 

sufficient 

rack 

protrudes  past  the  sprocket 
so that the limit actuators are 
able to be attached.

Remove the shims

Loosen the bolts holding the drive on the foundation plate; remove the 2-mm shims.
Retighten the four mounting bolts. This provides the correct engagement of the rack and 
pinion teeth.

Fit and adjust the limit actuator plates

Allow the gate to slide manually to each end position and fit the limit actuator plates to 
the rack, such that the limit switch is activated. This can be fine tuned after the power is 
connected to the drive.

gate

gate

40

100 min

30 min

1

2

3

4

Summary of Contents for G715D





























Reviews: