4-9
Specifications
Performance
(Sample Rate Converter bypassed)
Symbol
Description
Minimum
Typical
Maximum
Units
F
s
Sample Rate for Digital
TBD
48
96
kHz
Input Data
19
THD+N
Total Harmonic Distortion
0.00002
%
plus Noise
20
(RELATIVE)
IMD
Intermodulation Distortion
21
0
%
(SMPTE 4:1)
Jitter in Output Clock
415
pS
Tolerable Jitter in Input
35
nS
Clock before Loss of Lock
22
Resolution (input)
24
24
bits
Resolution (output)
24
24
24
bits
Frequency Response
23
+/-0
dB
Dynamic Range
24
Equal to Dynamic Range
dB
of input signal
Noise Floor
25
Equal to Noise Floor
dB
of input signal
Delay through receiver
26
2
WSR+periods
Delay through transmitter
27
43
/
64
WST+periods
Interchannel Phase Deviation
28
0
Degrees
MCLK+
Master Clock
29
TBD
12.288
24.576
MHz
WSR+
Receive Word Clock
30
(MCLK+)/256
Hz
WST+
Transmit Word Clock
31
(MCLK+)/256
Hz
SCKR+
Receive Bit Clock
32
(MCLK+)/4
Hz
SCKT+
Transmit Bit Clock
33
(MCLK+)/4
Hz
Z
in
Input Impedance
110
Ohms
Z
out
Output Impedance
110
Ohms
Miscellaneous
Overall Size:
8.40" long by 2.55" wide by 1.50" high
Weight:
3.8 Ounces
Input Connector:
3 Pin standard female XLR
Output Connector:
3 Pin standard male XLR
XLR pinout:
Pin 1 shield, Pin 2 positive input, Pin 3 negative input.
Input Data Format:
AES/EBU (AES3) Professional and S/PDIF. (IEC958) Consumer data formats are automatically identified and
correctly decoded.
Output Data Format:
AES/EBU Professional, regardless of input data format.
De-emphasis:
Not implemented; emphasis information from Channel Status Bits is relayed to host via Serial Peripheral
Interface (SPI).
Mutes:
Linked Left and Right input mute selectable via SPI control; linked Left and Right output mute selectable via
SPI control.
Serial Data Interface:
TBD
Synchronous Sampling:
Multiple outputs may be synchronized via DPDB signal on connector. MDM-1 transmitter is slaved to MCLK+,
WST+, and SCKT+ signals. MDM-1 receiver may be configured as Master, to generate MCLK+ (via AES_CLK),
WSR+, and SCKR+ signals derived from input data stream, or as Slave, to receive WSR+ and SCKR+ signals
from card-edge connector, either with or without the Sample Rate Converter. With sample rate converter
engaged, the MDM-1 cannot be configured as the master.
Unless otherwise noted:
Signal measurements are at unity gain, +16 dBu and 20 Hz to 20 kHz bandwidth.
Power measurements are quiescent.
Operating temperature with non condensing humidity
Summary of Contents for Integrated Signal Processor ISP-100
