background image

 

 

4.2.  DETAILED SAFETY PRINCIPLES. 

 
 
     4.2.1.  PREPARATION FOR WORK 

 

 

CAREFULLY read the  service manual.  Be  absolutely sure that  you are  acquainted  with  all 
the safety and mower operating instructions referring the preparation for work, transport and 
storage of the machine. 

 

If you do not follow the given instructions the producer do not answer for the possible harms 
or damages. 

 

 

THE USER should have  carefully buttoned up, not  too  loose clothing to  avoid  catching by 
protruding parts or possible driving into rotating parts. 

 

 

FOR DRIVING the mower use the PTO drive shaft with one-way clutch of the type given in 
the  manual.  Protect  shields  of  the  PTO  shaft  against  turning  according  to  the  PTO  shaft 
service manual.  
The PTO shaft must have complete shields.  
Do not use PTO shaft that is not working properly or has damaged shields. 

 

 

CONTROL the condition of the  mower, tighten the bolts and check the fastening of all the 
moving and protecting elements before linking the mower and tractor into a working unit.  

 

 

WHILE  CONNECTING  AND  DISCONNECTING  the  mower  to  and  from  the  tractor  be 
especially careful. 

 

 

VERY CAREFULLY approach the mower with the tractor to set the fastening points of the 
three-point  suspension  system  and  power  take-off  –  power  input  shafts  in  a  close  position. 
No person should be between the tractor and the mower at that time.  
All the operations of connecting the tractor with the mower should be executed only after 
you stop the engine, immobilize the tractor with a handbrake and take the ignition key off. 
 

 

ALWAYS make sure there is no people or animals near the mower, before lifting. 

 

 

DO  NOT  LEAVE  the  mower  in  lifted  position  on  the  tractor’s  three-point  suspension 
system.  

 

 

BEFORE  YOU  LEAVE  the  tractor  ALWAYS  lower  the  mower  onto  the  still  and  flat 
ground, stop the drive of PTO shaft, stop the engine, take the ignition key off. 

 

 

NEVER USE the mower without protective shields and aprons. Working without shields or 
with  damaged  shields  is  forbidden  because  of  the  danger  of  throwing  stones  or  other  hard 
objects by rotating drums. 

 

 

START  the  mower  after  setting  all  elements  in  working  position.  Starting  the  mower  in 
transport position is FORBIDDEN.  

 

 

BEFORE setting the mower in transport position, ALWAYS disconnect the PTO shaft from 
the tractor. 

 

 

NEVER start the mower in closed rooms due to harmful exhaust gases. 

 

Summary of Contents for Z 175-1


































Reviews: