background image

15 

Spraying 

 

Observe the instructions in the section entitled "Safety". 
Operate the device only while it is vertical or suspended upright and nearly vertical. 
Avoid allowing drops of spray to drift onto areas that are not being treated. 
Observe the instructions of the spray product manufacturer! 

1.  Suspend 

the 

device 

from 

your 

shoulder 

or 

place 

it 

on 

your 

back.  

(Fig. 11 and/or 12)

 

To prevent dripping, hold the spray lance up when first spraying and activate the shut-
off valve until no more liquid mixed with air is emerging. 

2.  Activate the shut-off valve [4]. 

(Fig. 13)

 

  Spraying may now begin.  

3.  Make  certain  the  optimum  spraying  pressure  is  set 

(

  Table  2) 

on  the  pressure 

gauge [15]. 

Spraying pressure 

Spraying quantity with nozzle 1302 

1.5 bar  (22 psi) 

0,49 l/min 

2.0 bar (29 psi) 

0,56 l/min 

3.0 bar (43,5 psi) 

0,69 l/min 

Table 2. Linear dependence: spraying rate and spraying pressure 

4.  If  the  spraying  pressure  decreases  more  than  0.5  bar  from  the  optimum  level,  pump 

some more. 

If liquid mixed with air emerges from the nozzle, the tank is empty. 

After usage 

 

Observe the instructions in the section entitled "Safety". 

1.  Pull up the red button on the safety valve [9] until all excess pressure is released from 

the tank. 

(Fig. 4)

 

2.  Remove the cover [10+11]. 

(Chapter entitled "Preparation" Points 2-3, Fig. 5)

 

3.  Dilute the remaining quantity twice in a row  with 1/2 liter of water each time and spray 

the resulting liquid onto the treated area. 

In the case of plant protection products dilute the remaining quantity twice in a row with 

1/2 liter of water each time and spray the resulting liquid onto the treated area.

 

 

Collect  and  dispose  of  the  residual  liquid  according  to  all  applicable  laws, 
requirements  and  regulations.  Observe  the  instructions  of  the  spray  product 
manufacturer! 

4.  Empty and rinse the device with clear water. 
5.  Wipe off the device with a moist cloth. 
6.  For drying and storing the device, keep the tank and pump in a dry place protected from 

sunlight and freezing temperatures.

 (Fig. 14)

 

 

Clean the protective equipment and yourself every time after usage. 

Summary of Contents for RESISTENT EXTRA 3592












Reviews: