7
English
19. BE CAREFUL OF DOUBLE FIRE DUE TO RECOIL.
If the push lever is unintentionally allowed to re-
contact the workpiece following recoil, an unwanted
fastener will be driven.
In order to avoid this undesirable double
fi
re,
1) Pull the trigger rapidly and
fi
rmly.
2) Use the probe to ensure nails were
fi
red
accurately into the holes.
20. DO NOT DRIVE FASTENERS INTO THIN
BOARDS OR NEAR CORNERS AND EDGES OF
WORKPIECE.
The fasteners can be driven through or away from the
workpiece and hit someone.
If fasteners are driven into hard materials such as
metal, the fasteners can ricochet and hurt someone.
21. NEVER DRIVE FASTENERS FROM BOTH SIDES
OF A WALL AT THE SAME TIME.
The fasteners can be driven into and through the wall
and hit a person on the opposite side.
22. CHECK FOR LIVE WIRES.
Avoid the risk of severe electrical shock by checking
for live electrical wires that may be hidden by walls,
fl
oors or ceilings. Turn o
ff
the breaker switch to
ensure there are no live wires.
23. DO NOT OVERREACH.
Keep proper footing and balance at all times.
24. NEVER USE NAILER WHICH IS DEFECTIVE OR
OPERATING ABNORMALLY.
If the Nailer appears to be operating unusually,
making strange noises, or otherwise appears
defective, stop using it immediately and arrange for
repairs by a metabo HPT authorized service center.
25. REMOVE ALL REMAINING FASTENERS AND
BATTERY FROM NAILER WHEN:
1) doing maintenance and inspection;
2) checking proper operation of push lever and
trigger;
3) clearing a jam;
4) it is not in use;
5) leaving work area;
6) moving it to another location; and
7) handing it to another person.
Never attempt to clear a jam or repair the Nailer unless
you have removed battery and all remaining fasteners
from the Nailer.
The Nailer should never be left unattended since people
who are not familiar with the Nailer might handle it and
injure the themselves.
26. REMOVE BATTERY FROM NAILER WHEN:
1) loading fasteners
27. STAY ALERT.
Watch what you are doing. Use common sense.
Do not operate the Nailer when you are tired.
The Nailer should never be used by you if you are
under the in
fl
uence of alcohol, drugs or medication
that makes you drowsy.
28. HANDLE NAILER CORRECTLY.
Operate the Nailer according to this Manual.
Never allow the Nailer to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
29. NEVER USE NAILER FOR APPLICATIONS OTHER
THAN THOSE SPECIFIED IN THIS MANUAL.
30. HANDLE NAILER CAREFULLY.
Do not drop the Nailer or strike the Nailer against
hard surfaces; and do not scratch or engrave signs
on the Nailer. Handle the Nailer carefully.
31. MAINTAIN NAILER WITH CARE.
Keep the Nailer clean and lubricated for better and
safer performance.
32.
USE ONLY PARTS, ACCESSORIES OR
FASTENERS SUPPLIED OR RECOMMENDED BY
metabo HPT.
Unauthorized parts, accessories, or fasteners may
void your warranty and can lead to malfunction and
resulting injuries.
Only service personnel trained by metabo HPT,
distributor or employer shall repair the Nailer.
33. NEVER MODIFY OR ALTER A NAILER.
Doing so may cause it to malfunction and personal
injuries may result.
34. NEVER allow magnets (or similar magnetic
devices) to be adjacent to the nailer, because the
nailer has a magnetic sensor inside.
Doing so will cause a failure or risk of injury by
malfunction.
35. Before each
fi
ring, be sure to set probe through
the metal hole.
This tool and nails are designed for metal connector
with pre-punched holes.
Drive nails into work surface only; never into materials
too hard to penetrate.
If the probe is not set properly, it could ricochet and
hurt yourself or someone.
If you are not sure to set the probe through the metal
hole, never drive nails.
Never drive nails into metal. Only drive into pre-
punched metal holes.
SAFETY
—
Continued
000Book̲NR3665DA̲metabo.indb 7
000Book̲NR3665DA̲metabo.indb 7
2021/02/22 12:20:24
2021/02/22 12:20:24
