background image

ENGLISH

en

8

Additional Warnings:

California Prop 65 08_2018

Some dust created by power 

sanding, sawing, grinding, 

drilling, and other construction activities 

contains chemicals known to cause cancer, 

birth defects or other reproductive harm. Some 

examples of these chemicals are:

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and 

other masonry products, and

• Arsenic and chromium from chemicallytreated 

lumber.

Your risk from these exposures varies, depending 

on how often you do this type of work. To reduce 

your exposure to these chemicals: work in a well 

ventilated area, and work with approved safety 

equipment, such as those dust masks that are 

specially designed to filter out microscopic 

particles.

3.3 Symbols on the tool

...........Class II Construction

V...............volts

A...............amperes

Hz.............hertz

W..............watts

~

..............alternating current

rpm ......... revolutions per minute

.../min ..... revolutions per minute

n ............. rated speed

See pages 2 and 3.

1 Bow  handle

2 Locking  discs

3 Thumb  screws 

4 Threaded holes on gear housing

5 Side handle *

6 Scale (chamfer height)

7 Adjusting ring (chamfer height)

8 Clamping screws on scale ring

9 Scale ring (chamfer height)

10 Speed adjustment wheel *

11 Electronic signal indicator *

12 Handle

13 Chip protection plate screws

14 Chip protection plates

15 Guide rail

16 Arrow = prescribed working direction

17 Scale (chamfer angle)

18 Screws (chamfer angle)

19 Indexable insert holder / milling head

20 Indexable insert

21 Fastening screw for indexable insert

22 Slide switch *

23 Paddle switch *

24 Lock *

25 Trigger*

26 Guide roller

27 Scale (pipe diameter)

*equipment-specific

Before commissioning, check that the rated 

mains voltage and mains frequency, as stated 

on the type plate match your power supply.

Always install an RCD (GFCI) with a maximum 

trip current of 30 mA upstream.

5.1 Attaching the additional handle

Only work with attached bow handle (1) or side 

handle (5) (depending on equipment)! Attach 

the handle as shown (see page 2, Fig. A).

Attach bow handle (1)

- Fit locking discs (2) to the left and right of the 

handle (1).

- Move the handle (1) with the locking discs (2) from 

the front to the gear housing.

- Insert the thumb screws (3) to the left and right of 

the handle (1) and turn gently.

- Adjust the handle (1) to the required angle.

- Firmly tighten the thumb screws (3) to the left and 

right manually.

Attach side handle (5) (depending on 

equipment, only for KFM 15-10 F, 

KFMPB 15-10 F):

When milling edges of small angles (setting < 

30°) depending on the working conditions it 

may be advantageous to use the side handle (5) 

rather than the bow handle (1). For larger angles

always use the bow handle (1) so that you can hold 

the machine securely. 
- Attach the side handle (5) on the

 right or left 

side 

of the machine and secure.

Pull the plug out of the socket before making 

any adjustments, changing tools, carrying out 

maintenance or cleaning.

Indexable inserts, holders for indexable 

inserts, the workpiece and chips can be hot 

after work. Wear protective gloves.

Danger of crushing! Wear protective gloves.

6.1 Setting the chamfer angle

1. Read the set angle on the scale (17).

2. Loosen the screws (13) and slide both chip 

protection plates (14) (on the left and right of the 

machine) upwards.

3. Loosen the screws (18) (front and back) and set 

the chamfer angle to the desired angle by 

turning the guide rail (15). Read the set chamfer 

angle on the scale (17).

4. Firmly tighten the screws (18) (front and back).

5. Slide both chip protection plates (14) (on the left 

and right of the machine) all the way down

Tighten the screws (13) (on the left and right of 

the machine).

6. Changing the chamfer angle also changes the 

chamfer height (due to the design). Therefore, 

4. Overview

WARNING

5. Commissioning

6. Setting

Summary of Contents for KFM 15-10 F

































Reviews: