ENGLISH
en
10
6.5 Changing the chuck (KHE .... Q)
Ensure a clean spindle (6) when changing the
chuck. Apply a light coating of grease to the
spindle. (Special grease: Order No.: 6.31800)
Only attach the Metabo chuck provided.
Removing the chuck:
See page 2, fig. C.
- Turn the chuck lock (3) in the direction of the arrow
until the stop (a) and remove chuck (b).
Replacing the chuck:
See page 2, fig. D.
- Put the chuck onto the spindle (6) (a).
- Turn the chuck lock (3) in the direction of the arrow
(b) until the chuck can be pushed completely onto
the spindle and release the chuck lock.
- Check to see that the chuck is properly seated.
Note:
To prevent the spindle from rotating when the
chuck is being changed, put the switch button (10)
to chiselling
.
6.6 Tool change with SDS chuck
Before fitting, clean tool shank and apply
special grease (accessories order no.
6.31800)! Use only SDS-Plus tools.
Inserting tools:
- Turn tool and insert until it engages. The tool is
automatically locked.
Remove the tool:
See page 2, fig. A.
- Pull tool lock (2) backwards in direction indicated
by arrow (a) and remove tool (b).
6.7 Tool change keyless chuck (KHE .... Q)
Use the keyless chuck when drilling without impact
into metal, wood etc. and for driving in screws.
Clamp tool
(see p.2, fig. B)
:
Turn sleeve (5) in direction “OPEN, RELEASE” (a).
Insert tool as deeply as possible (b) and turn sleeve
in the opposite direction, until any perceptible
mechanical resistance is overcome (c).
Caution!
The tool is not yet clamped!
Continue to turn vigorously
(you must hear a
“click”)
, until you cannot turn any further -
only
now
is the tool
safely
clamped.
Notes:
The rattling that might be heard after
opening the chuck (depending on the function) can
be eliminated by turning the sleeve into the other
direction.
With a soft tool shank, retightening may be required
after a short drilling period.
Always keep the
spindle (6)
clean and grease it a
bit. (Special grease: Order No.: 6.31800)
Cleaning the keyless chuck (4):
After prolonged use, hold the chuck vertically with
the opening facing downwards and fully open and
close it several times. The dust collected falls from
the opening. Regular use of cleaning spray on the
jaws and jaw openings is recommended.
Vent slots:
The vent slots of the machine should be cleaned
periodically.
If the trigger button (13) cannot be pressed, check,
if the rotation selector switch (11) is completely in
position R or L.
f
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
f
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
1
= Rated input
P
2
= Power output
n
1
= no-load speed
n
2
= on-load speed
s
max
= max. impact rate
W
= max. single impact force
D
1
= drill-Ø concrete with hammer drill bits
D
2
= drill-Ø masonry with core bits
7. Maintenance and Cleaning
8. Troubleshooting
9. Accessories
10. Repairs
11. Environmental Protection
12. Technical Data
