Metabo Ku 6870, Original Instructions Manual

ENGLISH

en

8

Original instructions

We, being solely responsible, hereby declare that 

these curve shears conform to the standards and 

directives specified on page 3.

The machine is designed for cutting through and 

trimming sheet material and cuttable plastics.
The user bears sole responsibility for damage 

caused by improper use.
Generally accepted accident prevention 

regulations and the enclosed safety information 

must be observed.

For your own protection and for the 

protection of your electrical tool, pay 

attention to all parts of the text that are 

marked with this symbol!

WARNING

 – Reading the operating instruc-

tions will reduce the risk of injury.

Pass on your electrical tool only together with these 

documents.

General Power Tool Safety Warnings

WARNING – Read all safety warnings and 

all instructions.

Failure to follow the warnings 

and instructions may result in electric shock, fire 

and/or serious injury. 

Save all warnings and instructions for future 

reference!

 The term "power tool" in the warnings 

refers to your mains-operated (corded) power tool 

or battery-operated (cordless) power tool.

3.1 Work area safety

a) 

Keep work area clean and well lit.

 Cluttered or 

dark areas invite accidents.

b) 

Do not operate power tools in explosive 

atmospheres, such as in the presence of 

flammable liquids, gases or dust.

Power tools 

create sparks which may ignite the dust or fumes.

c) 

Keep children and bystanders away while 

operating a power tool.

 Distractions can cause 

you to lose control.

3.2 Electrical safety

a) 

Power tool plugs must match the outlet. 

Never modify the plug in any way. Do not use 

any adapter plugs with earthed (grounded) 

power tools.

 Unmodified plugs and matching 

outlets will reduce risk of electric shock.

b) 

Avoid body contact with earthed or 

grounded surfaces, such as pipes, radiators, 

ranges and refrigerators.

 There is an increased 

risk of electric shock if your body is earthed or 

grounded.

c) 

Do not expose power tools to rain or wet 

conditions.

 Water entering a power tool will 

increase the risk of electric shock.

d) 

Do not abuse the cord. Never use the cord 

for carrying, pulling or unplugging the power 

tool. Keep cord away from heat, oil, sharp 

edges or moving parts.

 Damaged or entangled 

cords increase the risk of electric shock.

e) 

When operating a power tool outdoors, use 

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the 

risk of electric shock.

f)

If operating a power tool in a damp location is 

unavoidable, use a residual current device 

(RCD) protected supply.

 Use of an RCD reduces 

the risk of electric shock.

3.3 Personal safety

a) 

Stay alert, watch what you are doing and use 

common sense when operating a power tool. 

Do not use a power tool while you are tired or 

under the influence of drugs, alcohol or 

medication.

 A moment of inattention while 

operating power tools may result in serious 

personal injury.

b) 

Use personal protective equipment. Always 

wear eye protection.

 Protective equipment such 

as dust mask, non-skid safety shoes, hard hat, or 

hearing protection used for appropriate conditions 

will reduce personal injuries.

c) 

Prevent unintentional starting. Ensure the 

switch is in the off-position before connecting 

to power source and/or battery pack, picking 

up or carrying the tool.

Carrying power tools with 

your finger on the switch or energising power tools 

that have the switch on invites accidents.

d) 

Remove any adjusting key or wrench before 

turning the power tool on.

A wrench or a key left 

attached to a rotating part of the power tool may 

result in personal injury.

e) 

Do not overreach. Keep proper footing and 

balance at all times.

This enables better control of 

the power tool in unexpected situations.

f) 

Dress properly. Do not wear loose clothing or 

jewellery. Keep your hair, clothing and gloves 

away from moving parts.

Loose clothes, jewellery 

or long hair can be caught in moving parts.

g)

 If devices are provided for the connection of 

dust extraction and collection facilities, ensure 

these are connected and properly used.

Use of 

dust collection can reduce dust-related hazards.

3.4 Power tool use and care

a) 

Do not force the power tool. Use the correct 

power tool for your application.

The correct 

power tool will do the job better and safer at the rate 

for which it was designed.

b) 

Do not use the power tool if the switch does 

not turn it on and off.

Any power tool that cannot 

1. Conformity Declaration

2. Specified Use

3. General Safety Instructions