ENGLISH
en
11
Only use screwdriving bits with such plug-in
ends:
The screwdriving bit used must match the
screw.
Damaged screwdriving bits must not be used.
6.6 Changing SSW... screwdriving bits
Inserting screwdriving bit:
Fit the tool on the
square attachment (1) until the limit stop.
Removing screwdriving bit:
Pull the tool from the
square attachment (1).
The screwdriving bit used must match the
screw.
Damaged screwdriving bits must not be used.
Mount the machine on the screw, ensuring it is
aligned straight.
The screwdriving process has two elements:
inserting the screw
and
tightening the screw with the percussion mech-
anism.
The tightening torque depends on the impact dura-
tion.
With an impact duration of approx. 5 seconds, the
maximum tightening torque has been reached.
The torque curve depends on the type of applica-
tion:
With a hard screwdriving application (screw-
couplings in hard material such as metal), maximum
tightening torque is already reached after a short
impact duration (a).
With a soft screwdriving application (screw-
couplings in soft material such as wood), a longer
impact duration (b) is required.
Recommendation: determine the correct impact
duration by carrying out trial screwdriving.
Caution!
With
small screws,
maximum torque can
be reached even below an impact duration of 0.5
seconds.
- This is why the duration of the screwdriving
process must be monitored exactly.
- Set a suitable position on the setting wheel (7)
(see chapter 6.4).
- Adjust the tightening torque by pressing firmly or
lightly on the trigger (5), ensuring that the screw is
not damaged or that the screw head does not tear
off.
Only use original Metabo battery packs and Metabo
accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
See page 4.
A Chargers
B Battery packs with different capacity
Only use battery packs with the appropriate
voltage for your power tool.
C Screwdriving bits
For a complete range of accessories, see
www.metabo.com or the catalogue.
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-circu-
iting (e. g. by protecting them with adhesive tape).
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U
=Voltage of battery pack
n
0
=No-load speed
S
=Impact frequency
H
=Machine tool attachment
m
=Weight (with smallest battery pack)
M
P
= max. tightening torque (power mode)
7. Use
9,5 mm (3/8“)
8. Accessories
9. Repairs
10. Environmental Protection
11. Technical specifications
Summary of Contents for SSD 18 LTX 200 BL
