ENGLISH
en
11
Connect a suitable extraction device. Use a suction
hose with a 35 mm connector diameter.
7.2 Setting the oscillating frequency
The oscillating frequency can also be set during
operation by turning the adjustment wheel (6).
The best way to determine the ideal setting is
through a practical trial.
7.3 Switching On and Off
Switching on:
Move switch (5) to "
I
" position.
Switching off:
Move switch (5) to "
O
" position.
Empty clogged dust channel (9) (see page 2
fig. A)
- Loosen the screw with hexagon spanner (7).
- Remove dust channel (9) and empty.
- Insert dust channel (9).
- Insert screw with hexagon spanner and tighten.
Clean the machine regularly.
This includes
vacuum cleaning the ventilation louvres on the
motor.
Replace worn sanding plate (2) (see page 2 fig.
B)
- Remove fixing screw (on the underside of the
sanding plate (2)).
- Remove sanding plate (2).
- Put new sanding plate (2) in place (when putting in
position, turn sanding plate (2) until it engages on
the flattened bits of the carrier disc).
- Refit fixing screw (on the bottom side of the
sanding plate (2)) and tighten.
Readjust braking ring (4) (see page 3 fig. C)
When the braking force decreases, the braking ring
(4) can be readjusted. Loosen the screw and push
the braking ring (4) forward to the sanding plate (2)
until light contact is established. Tighten the screw
again.
Replace braking ring (see page 3 fig. D)
To change the worn braking ring (4) remove the
sanding plate (2), remove the tensioning band, (3)
remove the old braking ring (4) and put on the new
one until the stop. Refit the tightening band (3) and
sanding plate (2).
Note: If abrasive material (e.g. gypsum, etc.) is
being sanded, the braking ring inevitably wears
faster.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
For the complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must only be replaced with
a special, original mains cable from Metabo, which
is available only from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2002/96/EC
on waste electrical and electronic equipment and its
implementation in national legal systems.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D
=Diameter of sanding plate
P
1
=Rated input power
P
2
=Power output
n
0
=Idle speed
n
1
=Speed at rated load
S
=Oscillating circuit diameter
m
=Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
AC Power
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
h, DS
=Vibration emission value
(surface grinding)
a
h, P
=Vibration emission value
(polishing)
K
h,DS
/K
h,P
=Uncertainty (vibration)
8. Cleaning, Maintenance
9. Accessories
10. Repairs
11. Environmental Protection
12. Technical Specifications
Summary of Contents for SXE 400
