ENGLISH
en
10
Releasing the clamping nut:
- Lock the spindle (see chapter 7.1). Turn the
clamping nut (10) anticlockwise using the 2-hole
spanner (11) to unscrew.
8.1 Switching On and Off
Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off, keep it away from dust
deposits. After switching off the machine, only place
it down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands at the intended handles, take a secure
stance and concentrate on the work.
See illustration A on page 2.
Switching the angle grinder ON just for a
moment:
Switching on:
Press in the lock (4) and then press
the trigger switch (5). Let go of the lock (4).
Switching off: Release the trigger switch (5).
Continuous operation (depends on machine
features):
Switching on:
Press in the lock (4) and hold in place.
Press and hold the trigger switch (5). The
machine is now switched on. Now press in
the lock (4) a second time to lock the trigger
switch (5) in position (continuous operation).
Switching off: Press and release the trigger switch
(5).
8.2 Working instructions
Grinding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Roughing: position the machine at an angle of 30° -
40° for the best working results.
Separating:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Sanding:
Press down the machine evenly on the surface and
move back and forth so that the surface of the
workpiece does not become too hot.
Wire brushing:
Press down the machine evenly.
Motor cleaning:
blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Button (6) for adjustment of the handle:
Occasionally blow compressed air through the
button (when pressed, in all 3 main handle
positions).
Switching on procedures produce brief reductions
in voltage. Unfavourable power conditions can be
detrimental to other devices. Power impedances
smaller than 0.4 ohm should not cause any
malfunction.
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
The dealer needs to know the exact model
designation of your power tool in order to select the
correct accessory.
See page 4.
A Roughing disc (always use with safety guard
attached)
B Louver disc (always use with safety guard
attached)
C Parting safety guard.
D Parting disc (always use with parting safety
guard attached)
E Diamond discs (always use with parting safety
guard attached)
F Hand guard (for attaching under the additional
side-mounted handle.)
G Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx.
35 mm)
H Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
I Fibre discs (always use with the hand guard
attached.)
J Semi-flexible sanding discs (for use with elastic
supporting disc 6.23279) (always use with hand
guard attached.)
K Sanding pad with Velcro (always use with the
hand guard attached.)
L Adhesive sanding disc (always use with the
hand guard attached.)
M Adhesive fleece (always use with the hand
guard attached.)
N Steel wire brushes (always use with the hand
guard attached.)
8. Use
9. Cleaning
10. Troubleshooting
11. Accessories
