background image

SECTION 12 — ECOLOGICAL INFORMATION  

Ecotoxicity 

Fish: Mosquito Fish: LC50 = 138 mg/L; 96 Hr; Unspecified No data available 

Environmental 

The acidity of phosphoric acid may be reduced readily by natural water hardness minerals, but the 
phosphate may persist indefinitely. During transport through the soil, phosphoric acid will dissolve some of 
the soil material, in particular, carbonate-based materials. The acid will be neutralized to some degree with 
adsorption of the proton and phosphate ions also possible. However, significant amounts of acid will 
remain for transport down toward the groundwater table.  

Physical  

No information available 

 

SECTION 13 — DISPOSAL CONSIDERATIONS  

Chemical waste generators must determine whether a discarded chemical is classified as a hazardous waste. 
US EPA guidelines for the classification determination are listed in 40 CFR Parts 261.3. Additionally, 
waste generators must consult state and local hazardous waste regulations to ensure complete and accurate 
classification.  

RCRA P-Series:

 None listed.  

RCRA U-Series:

 None listed.

 

SECTION 14 — TRANSPORT INFORMATION 

Shipping Name 

Phosphoric Acid

 

 

Hazard Class 

8

 

UN Number 

3264

 

Packing Group 

III

  

SECTION 15 — REGULATORY INFORMATION 

[NOHSC] 

Classified as Hazardous according to criteria 

[Poisons Schedule] 

S6 

[Hazard Category] 

Corrosive  

[HSNO Approval Number] 

HSR001545 

This product has been classified in accordance with the hazard criteria of the 

Controlled Products Regulations (CPR) and the MSDS contains all of the information required by CPR.

 

SECTION 16 — OTHER INFORMATION  

MSDS Creation Date:

 05.01.15 

 

The information above is believed to be accurate and represents the best information currently available to us. 

However, we make no warranty of merchantability or any other warranty, express or implied, with respect to 

such information, and we assume no liability resulting from its use. Users should make their own investigations 

to determine the suitability of the information for their particular purposes. In no event shall Fisher be liable for 

any claims, losses, or damages of any third party or for lost profits or any special, indirect, incidental, 

consequential or exemplary damages, howsoever arising, even if Fisher has been advised of the possibility of 

such damages. 

End of MSDS 

 

Summary of Contents for EASYKleen Pro S-10
























Reviews: