background image

4

UB 10 | Version 2.01

Safety

Tips and recommendations

It is necessary to observe the safety notes written in 
these operating instructions in order to reduce the risk of 
personal injuries and damages to property. 

2.2 Requirements to staff

The different tasks described in this manual represent 
different requirements to the qualification of the persons 
entrusted with these tasks. 

Only persons reliable working procedures can be ex-
pected from, are allowed to perform all works. Persons 
the responsiveness of which is affected by e. g. drugs, 
alcohol or medication, are not allowed to work with the 
machine.

The qualifications of the personnel for the different tasks 
are mentioned below:

Operator

The operator is instructed by the operating company 
about the assigned tasks and possible risks in case of 
improper behaviour. Any tasks which need to be per-for-
med beyond the operation in the standard mode must 
only be performed by the operator if it is indicated in 
these instructions and if the operating company expres-
sively commissioned the operator.

Qualified personnel

Due to their professional training, knowledge and experi-
ence as well as their knowledge of relevant regulations 
the specialist staff is able to perform the assigned tasks 
and to recognise and avoid any possible dangers them-
selves.

Manufacturer

Certain works may only be performed by specialist per-
sonnel of the manufacturer. Other personnel is not au-
thorized to perform these works. Please contact our cus-
tomer service for the execution of all arising work.

2.3 Personal protective equipment

The personal protective equipment serves to protect per-
sons against impairments of safety and health while wor-
king. The staff member has to wear personal protec-tive 
equipment while performing different tasks on and with 
the machine which are indicated in the individual para-
graphs of these instructions.

The personal protective equipment is explained in the 
following paragraph:

CAUTION!

This combination of symbol and signal words indi-
cates a potentially dangerous situation which may 
lead to slight or minor injury if not avoided. 

NOTE!

This combination of symbol and signal words indi-
cates a potentially dangerous situation which may 
lead to material or environmental damage if not avoi-
ded.

Tips and recommendations

This symbol highlights useful tips and recommenda-
tions as well as information for an efficient and trou-
ble-free operation. 

WARNING!

Danger in case of insufficient quali-
fication of the staff!!

Insufficiently qualified persons cannot estimate the 
risks while using the vacuum cleaner and expose 
themselves and others to the danger of severe or let-
hal injuries.

-  Have all works only performed by qualified persons.

-  Keep insufficiently qualified persons out of the work-

ing area.

Eye protection

The goggles protect the eyes from flying parts and 
liquid splashes.

Protective gloves

The protective gloves serve to protect the hands 
against sharp components as well as against fric-
tion, abrasions or deep injuries. 

Safety boots

Safety boots protect the feet from being crushed, fall-
ing parts and slipping over on slippery ground. 

Protective clothes

Protective clothes are made of a tightly fitted fabric 
without the protruding parts of low tear strength. 

Summary of Contents for UB 10























Reviews: