background image

4

STILTS ASSEMBLY

TOOLS NEEDED:

  7/16” Wrench 
  7/16” Socket and Ratchet  
  #2 Phillips Screwdriver  

SIDE POLES ASSEMBLY  

1.

  Loosen Upper Side Pole Clamp bolt. 

2.

   Loosen Lower Side Pole Bracket and remove bolt Side Pole. 

3.

   Insert Lower Side Pole through the Upper Side Pole Bracket, 

then insert it into the Lower Side Pole Bracket. Lining 

Pole Clamp up the hole, carefully reinsert the bolt with 

washer through both the bracket and pole. Add the second 

washer and tighten the nut. Lift the pole to make sure  

it is attached properly.  

4.

   Slide the Upper Side Pole over the Lower Side Pole and 

through the Upper Side Pole Clamp. Tighten the bolt so the 

pole will not fall but can be moved and twisted. 

HEEL CUP ASSEMBLY AND ADJUSTING 

1.

   Install Heel Cup using the included screws, nuts  

and washers. Leave Heel Cup loose for now. 

2.

    Adjust Heel Cup on Foot plate to fit shoe. Slide Heel Cup  

in or out to adjust length of Foot Plate so your leg  

is aligned with the Upper Side Pole.

3.

    Make sure Heel Cup screws are fastened securely. 

HEIGHT ADJUSTMENT

1.

   Stand or sit in a comfortable position to try  

on the assembled stilt. 

2.

   Remove Height Adjustment Knobs and pull Upper Legs  

to the required length.

3.

   Place Leg Support Cuff on or above the calf muscle, below 

the knee joint. Make sure the knee can flex properly. 

4.

   Adjust the Upper Side Pole height by pulling up or pushing 

down. 

5.

   Remove stilt and tighten Upper Side Pole Clamp bolt  

to secure height. NOTE: Do not over-tighten the clamp  

as doing so can bend the tube and weaken the stilt. 

SIDEWAYS ADJUSTMENT 

1.

   Loosen Upper Side Pole Bracket bolt. This adjusts distance 

between Foot Plate and Upper Side Pole. 

2.

  While sitting, put stilt on. 

3.

   Push or pull Side Pole so that knee is aligned over foot, 

making sure leg is straight (knees not turned out). 

4.

  Tighten the Upper Side Pole Bracket bolt. 

LEG CUFF

ANKLE STRAP

UPPER SIDE 
POLE CLAMP

HEEL CUP

TOE STRAP

FOOT PLATE

UPPER 
ADJUSTER 
DISK

LOWER 
ADJUSTER 
DISK

FLOOR SOLE

HEIGHT 
ADJUSTMENT 
KNOB

CALF STRAP

UPPER SIDE POLE

UPPER SIDE 
POLE BRACKET

LOWER SIDE 
POLE

LOWER 
SIDE POLE 
BRACKET

UPPER LEG

FRANÇAIS

ESP
AÑOL

ENGLISH

Summary of Contents for BuildMan I-BMDS1830

























Reviews: