Metel 200M-2.0.4.ECA Installation Manual Download | Manualshive

Page: 11 / 11

background image

www.metel.eu

8.4

Indication of Optical Ring Failure or Sabotage

8.4.1 In case of ring interruption (failure or sabotage) the communication is

redirected in 30ms. The change of ring state (from 'loop' to 'backup') can be mapped
to a relay output on every switch.

8.4.2 Relay output state – depending on failure or sabotage:

Non-alarm state (under voltage and optical ring is closed)

Alarm state (optical ring open or supply failure)

For more information, see the Help for SIMULand software.

11/11

«
...
9
10
11

Summary of Contents for 200M-2.0.4.ECA












Reviews:

No comments

Related manuals for 200M-2.0.4.ECA

Brand: D-Link Pages: 357

EasySmart DGS-1100-08

Brand: D-Link Pages: 44

Brand: pathway Pages: 28

Brand: GE Pages: 302

Brand: DAB Pages: 56

Brand: Key Digital Pages: 31

Brand: Pathway connectivity solutions Pages: 34

Brand: National Instruments Pages: 12

Brand: Comm-Tec Pages: 10

Brand: Madison Pages: 2

Brand: H3C Pages: 96

Brand: NVision Pages: 86

Brand: WilTec Pages: 7

Brand: National Instruments Pages: 23

Brand: Blackberry Pages: 10

Brand: 3onedata Pages: 4

tekmarNet 4 User Switch 481

Brand: Tekmar Pages: 12

Brand: N-Tron Pages: 169

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands