Metel 200M-2.0.4.ECA Installation Manual Download | Manualshive

Page: 8 / 11

background image

www.metel.eu

8.1.5 Add the found devices to the workspace.

8.1.6 Select a device using the left mouse button and using the right mouse button

you can select „Configuration/Online configuration“.

8.1.7 Enter password. Default is “metel”.

8.1.8 In tab „IP“ insert required IP address, mask and gateway.

Confirm settings by pressing button „OK“ or „Apply“.

8/11

«
...
6
7
8
9
10
...
»

Summary of Contents for 200M-2.0.4.ECA












Reviews:

No comments

Related manuals for 200M-2.0.4.ECA

WJSX150 - SWITCHER - ADDENDUM

Brand: Panasonic Pages: 48

MSD-804FD Series

Brand: IDK Pages: 133

Brand: IDK Pages: 150

Brand: IDK Pages: 101

Brand: IDK Pages: 85

Brand: IDK Pages: 40

Brand: IDK Pages: 97

Brand: IDK Pages: 117

Brand: IDK Pages: 77

Brand: Cole Hersee Pages: 2

Brand: Quintum Pages: 2

SkyEdge II-c Capricorn Pro 4 AC Series

Brand: Gilat Pages: 2

Brand: XtendLan Pages: 24

LS-5500-28C-PWR-SI-OVS

Brand: H3C Pages: 86

Brand: ALFAtron Pages: 15

Brand: AETEK Pages: 2

Brand: SignaMax Pages: 6

SANbox 5000 Series

Brand: Qlogic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands