Metel 200M-2.0.4.ECA Installation Manual Download | Manualshive

Page: 9 / 11

background image

www.metel.eu

8.2

Local Management

8.2.1 Connect the device to a computer using USB-A-B cable (not included).
8.2.2 Install driver – for download from

www.metel.eu

(at32uc3xxx_cdc.inf)

8.2.3 Verify correct port assignment in Device manager.
8.2.4 Launch SIMULand – for download from

www.metel.eu

8.2.5 In menu select „Tools/USB Device“.

8.2.6 Select the port assigned by the system and press the „Configuration“ button.

8.2.7 Enter password. Default is “metel”.

8.2.8 Continue with steps defined in Remote management (8.1.8)

9/11

«
...
7
8
9
10
11
»

Summary of Contents for 200M-2.0.4.ECA












Reviews:

No comments

Related manuals for 200M-2.0.4.ECA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 281

Brand: FAAC Pages: 2

Brand: Kathrein Pages: 8

Brand: Nayar Systems Pages: 21

Brand: Kathrein Pages: 24

Brand: Kasia Pages: 5

Raritan Dominion LX II

Brand: LEGRAND Pages: 7

Brand: LEGRAND Pages: 30

Brand: Harman Pages: 50

Brand: Tabs Pages: 4

Brand: Milestone pro Pages: 32

Brand: Versa Technology Pages: 26

Personal MiniHub

Brand: Black Box Pages: 22

Brand: PIKA Pages: 7

Brand: ATEN Pages: 21

Brand: Gefen Pages: 9

Brand: Eaton Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands