background image

12 

In-Warranty Repairs and Replacement – All Countries 

Please read the warranty statement that follows, and check your battery 
before requesting repair. During the warranty period any defective test tool 
can be returned to your Meterman Test Tools distributor for an exchange 
for the same or like product. Please check the “Where to Buy” section on 
www.metermantesttools.com for a list of distributors near you. Additionally, 
in the United States and Canada In-Warranty repair and replacement units 
can also be sent to a Meterman Test Tools Service Center (see below for 
address).

 

Non-Warranty Repairs and Replacement – US and Canada 

Non-warranty repairs in the United States and Canada should be sent to a 
Meterman Test Tools Service Center. Call Meterman Test Tools or inquire at 
your point of purchase for current repair and replacement rates. 
 

In USA 

In Canada 

Meterman Test Tools 

Meterman Test Tools 

 

1420 75th Street SW 

400 Britannia Rd. E. Unit #1 

 

Everett, WA 98203 

Mississauga, ON L4Z 1X9 

 

Tel: 888-993-5853 

Tel: 905-890-7600 

 Fax: 

425-446-6390 Fax: 

905-890-6866 

Non-Warranty Repairs and Replacement – Europe 

European non-warranty units can be replaced by your Meterman Test Tools 
distributor for a nominal charge. Please check the “Where to Buy” section 
on www.metermantesttools.com for a list of distributors near you. 
 

European Correspondence Address*  

 

Meterman Test Tools Europe 

 

P.O. Box 1186 

 

5602 BD Eindhoven 

 The 

Netherlands 

*(Correspondence only – no repair or replacement available from this 
address. European customers please contact your distributor.) 

Summary of Contents for PM55





















Reviews: