background image

8.4.2016

METOS Ardox IEC

10

 |

4.3.  After use

4.3.1.  Cleaning and Maintenance

Use of water hose or pressure  cleaning jet is strictly forbidden.

When cleaning the ceramic hob surface, remember that it is hot for a long time after use.

Ceran-glass Hob

Clean glass with hot soapy water and a soft cloth. Do NOT use metal scrapers.

The cleaning of ceramic hob surface is identical to cleaning of other similar surfaces  like glass.

Do not use corrosive or abrasive agents such as grill-and oven-sprays, stain- and rust removers, scouring 

powder and rough sponges. Cleaning is much easier if possible spill-overs are removed immediately with 

damp cloth.

Sugar and mixes containing much sugar must be removed immediately, because later removing is labori-

ous and may leave permanent marks.

Burned spillovers are easy to remove with a scrapper especially intended for cleaning ceramic hob sur-

faces.

If plastic or aluminum foils melt on the ceramic hob surface, they can be also removed with a scraper. For 

cleaning always prefer chemical cleaning methods rather than mechanical rubbing. Use a slightly alkaline 

detergent  (pH 8-10) diluted in water according to instructions when cleaning the surfaces of the range.

The grease  filter protecting air intake in the bottom of the unit must be cleaned regularly. A clogged 

grease  filter can cause  overheating,  power reduction or even malfunction.

Stainless Steel Surfaces

These surfaces should be cleaned with hot water and detergent then dried and polished with a soft cloth.

Cleaning agents containing bleach, abrasives or caustic chemicals will damage or stain the stainless steel 

surfaces and must not be used.

Badly stained,  removable parts should be soaked in hot water with an approved detergent.

If parts are not able to be removed, the application of warm water with approved detergent  using nylon 

or scotch  cleaning pads  will provide good result. 

4.3.2.  Other service measures

The appliance does not include any user serviceable parts inside. Service must be done by authorised 

service personnel only. 

STOP

STOP

Summary of Contents for IEC4

























Reviews: