background image

3

8.4.2016

METOS Ardox IEC

1.  General

Carefully read the instructions in this manual as they contain important information regarding proper, ef-

ficient and safe installation, use and maintenance of the appliance.

Keep this manual in a safe place for eventual use by other operators of the appliance.

The installation of this appliance must be carried out in accordance with the manufactur- er’s instructions 

and following local regulations. The connection of the appliance to the electric and water supply must be 

carried out by qualified persons only.

Persons using this appliance should be specifically trained in its operation.

Switch off the appliance in case of failure or malfunction. The periodical function checks requested in the 

manual must be carried out according to the instructions. Have the appli- ance serviced by a technically 

qualified person authorized by the manufacturer and using original spare parts.

Not complying with the above may put the safety of the appliance in danger.

The manufacturer does not take responsibility for any damages in case the operation in- structions and 

warnings contained in this manual are neglected.

1.1.  Symbols used in the manual

This symbol informs about a situation where a safety risk might be at hand. Given instruc- tions are man-

datory in order to prevent injury..

This symbol informs about the right way to perform in order to prevent bad results, appli- ance damage 

or hazardous situations.

This symbol informs about recommendations and hints that help to get the best perform- ance out of 

the appliance.

1.2.  Symbols used on the appliance

This symbol on a part informs about electrical terminals behind the part. The removal of the part must be 

carried out by qualified persons only.

1.3.  Checking the relationship of the appliance and the manual

The rating plate of the appliance indicates the serial number of the appliance. If the man- uals are miss-

ing, it is possible to order new ones from the manufacturer or the local repsentative. When ordering new 

manuals it is essential to quote the serial number shown on the rating plate 

STOP

 

 

Summary of Contents for IEC4

























Reviews: