2.11.2005
Rev. 1.5
Troubleshooting
51
The kettle does not tilt
The lid of the kettle is on and the mixer display
shows a 'Lid' signal
Open the lid
The emergency/stop button is pushed
Release the emergency-stop switch by turning it
clockwise
The ON/OFF switch is not in the ON position
Push the switch to the ON position
Other technical fault
Contact qualified technical personnel
The mixer does not start
The emergency/stop button is pushed
Release the emergency-stop switch by turning it
clockwise
The lid and the safety grid are not in their correct
positions on the kettle, the mixer display shows
a 'Lid' signal
Place the lid and safety grid in their correct posi-
tions on the kettle and restart
No mixer mode has been selected after selecting
the mixer
First select the mixer function and then select the
mixing (see the user manual ”Mixing func-
tions”)
The fuses in the main fuse box are blown/trig-
gered
Change/excite the fuses
All above mentioned sections have been
checked, both red error lights on the control pan-
el are flashing
The safety switch of the safety grid is damaged
and for safety reasons the operation of the mixer
is inhibited. Contact qualified technical person-
nel.
Other technical fault
Contact qualified technical personnel
The mixer stops during
mixing
The lid and the safety grid are not in their correct
positions on the kettle, the mixer display shows
a 'Lid' signal
Place the lid and safety grid in their correct posi-
tions on the kettle and restart
The emergency/stop button has accidentally
been pushed
Release the emergency-stop switch by turning it
clockwise
A pre-set program including stopping of the
mixer is in use
Check if a pre-set program is in use
The stuff to be mixed is too thick or there is too
much contents in the kettle
Make the contents of the kettle thinner or reduce
the amount and restart
Other technical fault
Contact qualified technical personnel
Timing of the kettle not
possible
The kettle is not returned to an upright position
after tilting, the temperature display shows a
'PoS' signal
Press the tilting reverse button until the kettle is
totally horizontal and the temperature display
shows an 'On' signal
The lid and the safety grid are not in their correct
positions on the kettle, the mixer display shows
a 'Lid' signal
Place the lid and safety grid in their correct posi-
tions on the kettle
Other technical fault
Contact qualified technical personnel
The automatic water fill-
ing does not fill any water
into the kettle
The shut-off valve of the water supply line is in
the closed position or the whole water supply
network is closed, an 'Err' message is blinking
on the water fill display.
Open the shut-off valve or wait until the water
supply is restored, and start the automatic water
fill again.
Other technical fault
Contact qualified technical personnel
It is not possible to acti-
vate the EasyRun pro-
gram
The kettle is not returned to an upright position
after tilting, the temperature display shows a
'PoS' signal
Press the tilting reverse button until the kettle is
totally horizontal and the temperature display
shows a 'On' signal
The lid and the safety grid are not in their correct
positions on the kettle, the mixer display shows
a 'Lid' signal
Place the lid and safety grid in their correct posi-
tions on the kettle
Other technical fault
Contact qualified technical personnel
The automatic cooling
program is interrupted al-
though the set tempera-
ture is not reached
The temperature of the cooling water is so high
that it is not possible to reach the set tempera-
ture, the reached temperature is flashing on the
temperature display
Select a final temperature that is possible to
reach with the temperature of the cooling water
at hand. If there is a need for lower temperatures,
please contact an authorized Metos dealer for in-
formation on ice bank cooling systems.
Summary of Contents for PROVENO S 100
