INSTALLATION
For
m
No. TMCEM-0212
6
General
The Toast-Max™ Electric Conveyor Toaster is shipped
w
ith all
co
m
ponents pre-asse
m
bled. Care should be taken
w
hen
unpacking the shipping carton to avoid da
m
age to the unit and
the co
m
ponents enclosed.
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 21°C (70°F).
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
FIRE HAZARD:
• Locate unit a minimum of 25 mm (1″) from combustible
walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
• Do not place anything on top of toaster. Do not place
toaster near or underneath curtains or other
combustible materials. Items near or on top of toaster
could catch fire causing injury and/or damage to the
toaster.
1. Re
m
ove the unit fro
m
the carton.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Re
m
ove tape and protective packaging fro
m
all surfaces of
the unit.
3. Place the unit in the desired location.
•
L
ocate the unit in an area
w
here the a
m
bient air
te
m
perature is constant and a
m
ini
m
u
m
of 21°C (70°F).
Avoid areas that
m
ay be subject to active air
m
ove
m
ents
or currents (i.e., near exhaust fans/hoods and air
conditioning ducts).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the
w
eight of the unit and food product.
• Make sure all the feet on the botto
m
of the unit are
positioned securely on the countertop.
4.
L
evel the unit by turning the
adjustable tip on each leg, if
necessary. Use a 16
mm
(5/8″)
open-end
w
rench to
m
ake
leveling adjust
m
ents.
5. Install the cru
m
b tray.
a. Position the cru
m
b tray
directly belo
w
the stop pins under the conveyor belt at
the front of the toaster.
b. Slide the cru
m
b tray into the toaster until the front of the
cru
m
b tray
m
eets the stop pins.
6. Install the front discharge chute or rear discharge tray to
the rear of the unit. Refer to the “Front or Rear Discharge
Installation” procedure in this section.
WARN
I
NG
L
engthen
Shorten
Adjustab
l
e
Tip
Installing the Cru
m
b Tray
Front or Rear Discharge Installation
Toast-Max units can be set up so toasted product discharges at
either the front or the rear of the unit.
For front discharge:
1. Slide the front discharge chute underneath the toaster.
2. Angle the curved end of the chute up slightly to place the
lip of the chute over the rear pins (one on each side).
3. Pull shut the discharge vane so it is in the closed position.
Front Discharge (Rear Vie
w
)
For rear discharge:
1. Re
m
ove the front discharge chute if it is installed.
2. Align the notches on the rear discharge tray over the t
w
o
set pins and lo
w
er into place.
3. Push open the discharge vane so it rests on the pins inside
of the unit.
Rear Discharge (Rear Vie
w
)
Stop
Pins
Cru
m
b
Tray
Discharge
Vane
(Open)
Set
Pin
Discharge
Vane
Hand
l
e
Rear
Discharge
Tray
Discharge
Vane
(C
l
osed)
Discharge
Vane
Hand
l
e
Front
Discharge
Chute
