background image

99-7804

7

Wiring Instructions

Harnesses Included:

• 24-pin gray Honda connector to 14-pin black interface connector, with

pre-wired 12-pin black ASWC-1 harness.

• 24-pin and 12-pin gray Honda connector to 22-pin black interface connector, 

with a Yellow female RCA.

• 8-pin gray Honda subwoofer connector to 

White

 RCA.

Blue

 connector to 

White

 connector LVDS cable.

Connections to be made:
From the 24-pin gray Honda connector to the aftermarket radio:

• Connect the 

Red

 wire to the accessory wire.

• Connect the 

Black

 wire to the ground wire.

• Connect the 

Yellow

 wire to the battery wire.

• Connect the 

Blue/White

 wire to the amp turn on wire 

(this wire must be

connected to hear sound from the factory amplifier)

.

• Connect the 

White

 wire to the left front positive speaker output.

• Connect the 

White/Black

 wire to the left front negative speaker output.

• Connect the 

Gray

 wire to the right front positive speaker output.

• Connect the 

Gray/Black

 wire to the right front negative speaker output.

• Connect the 

Green

 wire to the left rear positive speaker output.

• Connect the 

Green/Black

 wire to the left rear negative speaker output.

• Connect the 

Purple

 wire to the right rear positive speaker output.

• Connect the 

Purple/Black

 wire to the right rear negative speaker output.

Summary of Contents for 99-7804











Reviews: