background image

Chapter II 

Portable digital multimeter 

19 

1.3. Safety 

devices 

 

  The battery unit and fuses cannot be accessed without first disconnecting the measuring 

leads. 

  When measuring voltages above 24 V, the symbol blinks 

 on the display. 

 

  If the maximum range is repeatedly exceeded, an intermittent audible signal indicates the 

risk of electric shock. 

 
 

1.4. Warranty 

 

This equipment is warranted against any defects of manufacture or materials according to the 
general conditions of sale.  

 
During the warranty period (3 years), defective parts will be replaced, the manufacturer 
reserving the right to repair or replace the product. In the event of the equipment being returned 
to the after sale department or to a local agency, carriage to the centre shall be payable by the 
customer. 
 
The warranty does not cover the following : 

 

 

Repairs necessitated by misuse of the equipment or use in association with incompatible 
equipment. 

 

 

Modification of the equipment or any related software without the explicit authorization of 
the manufacturer. 

 

 

Repairs necessitated by attempts to repair or maintain the product made by a person not 
approved by the manufacturer. 

 

 

Adaptation to a specific application not provided for in the specifications of the equipment 
or the user manual. 

 

 

Damage after a drop, a shock or flooding. 

 

The contents of this manual must not be reproduced in any form whatsoever without the 
consent of the manufacturer. 

 

 
 

1.5. 

Maintenance and metrological verification 

 
Return your instrument to your distributor for any work to be done within or outside the 
guarantee. 

 
 

1.6. 

Unpacking - Repacking 

 

This equipment has been fully checked out mechanically and electrically before shipping. 
All precautions have been taken to ensure that the instrument arrives at its destination 
undamaged. 

 

However, it is advisable to carry out a rapid check for damage sustained in shipping. 
If there is any evidence of damage, make this known immediately to the shipper. 

 

*

 

Caution  

Should you need to return the multimeter, preferably use the original 

 

packaging and indicate the reasons as clearly as possible on an  

 accompanying 

note. 

 

 

 

Summary of Contents for MX 58HD




















Reviews: