background image

Doc# 

M9005 • REV N

 (May 2017) Page 

11 of 12

 

HAZARDOUS AREA APPROVALS

IECEx Approval 

(World)

IEC Markings:

Ex d IIB + H2 T4 Gb                                    

Ta -20°C to +85°C 

(no display)

Ta -10°C to +70°C (display)

IECEx LCI 11.0016X

IEC Standards:

IEC60079-0:2011

IEC60079-1:2007

WARNING-EXPLO

-

SION HAZARD-DO 

NOT DISCONNECT 

WHILE CIRCUIT 

IS LIVE UNLESS 

AREA IS KNOWN 

TO BE NON-HAZ

-

ARDOUS.

AVERTISSE-

MENT-RISQUE 

D’EXPLOSION. NE 

PAS DEBRANCHER 

TANT QUE LE 

CIRCUIT EST 

SOUS TENSION, 

A MOINS QU’IL 

NE S’AGISSE D’UN 

EMPLACEMENT 

NON DAN

-

GEREUX.

ATEX Approval 

(Europe)

ATEX Markings:

      II 2G Ex d IIB + H2 T4 Gb                             

Ta -20°C to +85°C 

(no display)

Ta -10°C to +70°C (display)

     

          LCIE 02 ATEX 6157X         

EN Standards:

EN60079-0:2012

EN60079-1:2007

UL Approval 

(North 

America)

CSA Markings:

 

         

Class I, Div 1, Groups B,C,D, 

T4A, NEMA 4/4X 

Class I, Div 2, Groups B,C,D, 

T4A, NEMA 4/4X

UL/CSA Standards:

UL 50

UL 508

UL 1203

UL 61010

CSA C22.2 No.25

CSA C22.2 No. 30

CSA C22.2 No. 94

CSA C22.2 No. 142

CSA C22.2 No. 213

CSA C22.2 No. 61010

ANSI/ISA 12.12.01-

2007

1180

Summary of Contents for SW6000













Reviews: