Edit Existing User Code:
Edit Existing CS Code:
Add or Change Card ID:
Edit Existing CS Code:
Adjust the Display Contrast:
Note:
Note:
Note:
Note:
Cannot change User Code itself but can edit information tied to
User Code (e.g., PIN).
- Press OK key to wake up touch pad.
- Enter User Code and press OK.
- Press "FUNCTION" key several times until "CHANGE THE
OPERATOR PIN" is displayed.
- Enter current PIN or Press OK if there is no current PIN.
- Enter New PIN or Press OK to skip.
- Press OK to accept new PIN or "CLEAR" to change PIN.
- Press "SIGN OUT" to exit & lock cart.
Cannot change User Code itself but can Edit information tied to
User Code (e.g., PIN).
- Press OK key to wake up touch pad.
- Enter User Code and press OK.
- Press "FUNCTION" key several times until "CHANGE CS PIN?" is
displayed.
- Enter current PIN or Press OK if there is no current PIN.
- Enter New PIN or Press OK to skip.
- Press OK to accept new PIN or "CLEAR" to change.
- Press "SIGN OUT" to exit & lock cart.
Only for carts that is equipped with a card reader. This function
can be performed by the Supervisor or User. The cart main lock must
be disengaged.
- Press OK key to wake up touch pad.
- Enter User Code and press OK.
- Press "FUNCTION" key several times until "SET OR CHANGE YOUR
CARD ID" is displayed & Press OK.
- Follow prompts. If using a magnetic card or bar code reader, slide the
card through the reader from back to front. If using a proximity card,
pass it over the reader.
- If the card is not properly read an Error Reading Card message will
display. Try swiping the card again (try not to angle the card as it
passes through or in front of the reader).
- When the card is read the message "NEW CARD ID IS 12345678".
Press OK to accept or clear to change.
- Press "SIGN OUT" to exit User Mode.
Cannot change CS Code itself but can Edit information tied to
CS Code (e.g., PIN).
- Press OK key to wake up touch pad.
- Enter User Code and press OK.
- Press "FUNCTION" key several times until "CHANGE CS PIN?" is
displayed.
- Enter current PIN or Press OK if there is no current PIN.
- Enter New PIN or Press OK to skip.
- Press OK to accept new PIN.
- Press "SIGN OUT" to exit & lock cart.
- Press OK to wake up touch pad.
- Enter Service Code and press OK.
- Press "FUNCTION" key several times until "ADJUST THE DISPLAY
CONTRAST" is displayed & Press OK.
- Press and hold down the side arrow keys < to decrease or > to
increase the contrast.
- Press OK.
- Press "SIGN OUT" to exit Service Mode.
If the cart fails to unlock or relock in this test, it may be because
the cart's Servomotor is not properly calibrated (see section below)
lock failures may also be due to jammed drawers or an improperly
adjusted cart lock switch.
- Lock the cart manually before starting this test.
- Press OK to wake up touch pad.
- Enter Service Code and press OK.
- Press "FUNCTION" key several times until "UNLOCK CART" is
displayed & Press OK, the cart will unlock.
- Press OK to relock the cart.
- If the cart fails to unlock or relock, an appropriate message will be
displayed.
- Press "SIGN OUT" to exit Service Mode.
Only for carts that are equipped with a Controlled Substance
drawer. For security reasons, narcotics drawers can only be opened by
an authorized person with a valid CS ID Code.
- Unlock the cart's main lock (see Section 2).
- Press the CS key and enter a valid CS ID code to unlock the CS
drawer with a key.
- The display reads "NARC DRAWER UNLOCKED".
- Pull the drawer open. The Servomotor should rotate a small cam
approximately 1/4 turn to push the drawer latch past its stop. If it does
not open, the CS drawer may not be configured (see section below),
or the servo or cable may be at fault, contact the Metro Customer
Service.
- If the drawer does not open, unlock it with a metal key to test the
drawer switch.
- Open and close the drawer, the display should change from "NARC
DRAWER OPEN" to "NARC DRAWER UNLOCKED".
- The NARC drawer switch test can also be performed by pulling the
drawer forward while it is locked. The display should change as
described above.
- If the drawer fails the switch test, close and lock the drawer. Sign out
then sign in again using the Service ID number.
- Press "FUNCTION" key several times until "TEST KEYPAD AND
SWITCHES" is displayed.
- Try the switch test again. If the drawer location number displays on
the right upper part of the display, the switch is functioning.
- If it does not, the drawer may not be configured (see section below or
contact Metro Customer Service).
- Press "SIGN OUT" to exit Service Mode.
- Press OK to wake up touch pad.
- Enter Service Code and press OK.
- Press "FUNCTION" key several times until "TEST THE KEYPAD AND
SWITCHES" is displayed & press OK.
-PRESS VARIOUS KEYS AND CHARACTERS WILL DISPLAY AS
SHOWN BELOW ON CHART.
-Press OK once and an "O" will appear in the upper part of the screen,
Press OK again to exit the test.
-Press "SIGN OUT" to exit Service Mode.
Unlock the Cart:
Test Keyless CS (Narcotic) Drawers:
Check the Keyless CS Drawer's Servomotor:
Test the Keyless CS Drawer Switches:
Keypad Test
Note:
Note:
FL420
Electronic Locking User Guide - General Operating Instructions
continued...
Section 7: User Code Functions
Section 8: CS Code Functions
Section 9: Service Code Functions
4
